DBXR463GG2CC General Electric Dryer - Instructions

Hardest part was rustling up the proper screw driver. 1) Unplug dryer from outlet. 2) Pull plastic knobs off all switches. 3) Remove screws and remove control panel. 4) Remove rotary switch by gently prying up on hold-down arm and twisting entire switch mechanism. 5) Remove wires one at a time and attach to corresponding spade lugs on new switch. 6) Install switch and twist into place. 7) Replace panel. 8) Replace control knobs. Under 20 minutes.

My dryer was making a loud stretching sound which I thought, because of previous experience, could be fixed by replacing the bearing slides. The problem turned out to be that the blower wheel that is attached to the motor was loose. I pushed the blower wheel all the way in so that about 1/4" of the motor shaft sticks out. I then tightened the bolt with a socket wrench. Problem solved.

At first I thought it was the belt but when I took off top portion of dryer I saw belt was fine. I got to this site and found source of noise was drum bearings from postings. I ordered the parts and much to my suprise had it working with 15 minutes. Web site was very helpful.

First dis connect from power sourse remove knob and the four screws that secure that instrument panel from machine.With a simple twist removed the defective switch,inserted new switch, transfered wires from old switch to new, replaced the panel and knob, reconnected power cord and it's done. Total time for this repair was less than ten minutes.

Watched video first, then diagnosed trouble. Went to internet for cost and avalible parts. Copied parts diagram. Very pleased with price and orderd parts assosiated with front drum. 4 days later parts arrived.

After unplugging the dryer, I removed the rear cover of the control area by removing 3 phillips screws on the back of the dryer - There is also a lower small panel that will come out along with the rear control panel cover during this operation. Next I removed 4 T20 Star type screws on the top painted edge of the control panel. The panel then tilted forward allowing good access to the start switch. I removed the switch from the panel WITHOUT taking off the wires as I wanted to verify that I was getting the wires transfered correctly. Both the new and old switch have number designations by the connection terminals. Once I had transfered the wires to the new switch by associating the numbers on the switch. The terminal with two wires has a little adapter that comes out with the two wires. I placed the new switch into the hole on the control panel, gave it a twist to engage the holding clips and when rotated into place, the switch "clicked" as it locked the little arm that sticks out of the side of the switch into place. Reassembly of the panels was easy, just put the panels back into place and torque down the screws and replace the control knob. Even though I had to purchase a set of stardrivers to complete this repair, the whole repair process ran only $30.00 and I ended up owning a set of star-screwdrivers. The last time Mr. Repairguy was here it ran over $200.00! Also, the documentation offered by Parts Select made locating and getting access to the switch fairly easy.

Thanks to the Part Select YouTube videos, I was able to determine how to disassemble the dryer without having to spend much time trying to fixure that evolution out, and I was pretty much able to troubleshoot what the potential problems (and fixes) were via the various Part Select videos (drum slide(s) install, bearing install). The only part that took a bit of time to install was the drum rear bearing. It is an easy install, but it was helpful to have my son hold the bearing from the back (outside) of the drum while I tighten the screws from the inside of the drum. Again, watching the Part Select videos beforehand is a must!

followed instructions that came with kit. The problem was the instructions were not very clear with regard to the "type" of burner. the "A" type with the slot is explained but the "B" without the slot wasen't clearly explained. Even that wasen't too bad (I had to re-do that part), But you need to be 20 years old to see the damned print. I had to use my reading glasses AND a magnifying glass to read them. Also with the "B" type burner, which I have, you simply install the limiter part and you don't need (can't) adjust it.

Had to tap three holes in the rear bearing to match the three attachment screws. Screw up with the part.

it was easy, it clip right on.needed to give it a little tap to get it in .

Followed the videos on this web site and found out how easy it was to replace the belt,drum glides and felt seals. I took my time and also completely cleaned out the gas dryer from all the lint. Thank you for the great prices, fast shipping and how to videos. Bill d.