Models > DBXR453GT2WW > Instructions

DBXR453GT2WW Dryer - Instructions

All Instructions for the DBXR453GT2WW
781 - 795 of 989
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
dryer never converted from natural to propane gas
followed instructions that came with kit. The problem was the instructions were not very clear with regard to the "type" of burner. the "A" type with the slot is explained but the "B" without the slot wasen't clearly explained. Even that wasen't too bad (I had to re-do that part), But you need to be 20 years old to see the damned print. I had to use my reading glasses AND a magnifying glass to read them. Also with the "B" type burner, which I have, you simply install the limiter part and you don't need (can't) adjust it.
Parts Used:
Natural Gas to Liquid Propane Conversion Kit
  • jeffrey from shirley, NY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Holes were not threaded on rear bearing kit
Had to tap three holes in the rear bearing to match the three attachment screws. Screw up with the part.
Parts Used:
Rear Drum Bearing Kit
  • Dennis G from Naples, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Was this instruction helpful to you?
Thank you for voting!
clip on door broke
it was easy, it clip right on.needed to give it a little tap to get it in .
Parts Used:
Door Strike
  • edward from early branch, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
It woud begin to heat and dry clothes then it would stop heating before the clothe dried.
Parts Select said 27% chance it was the coils and 26% chance it was moisture sensor. I ordered the coils and it did not fix the problem, my luck. I have now ordered moisture sensor and the next possible part, the cycling thermostat. If one of these solve the problem I will still have much less invested than a repairman would charge.
Parts Used:
M Series New Style Coil Kit
  • Thomas from Bath, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Squealing,Drum Wont Spin
Followed the videos on this web site and found out how easy it was to replace the belt,drum glides and felt seals. I took my time and also completely cleaned out the gas dryer from all the lint. Thank you for the great prices, fast shipping and how to videos. Bill d.
Parts Used:
Drum Bearing Slide - Green (Sold individually) Lint Filter - White Frame Door Latch Duct Felt Seal Drive Belt Front Drum Bearing Drum Bearing Slide - White (Sold individually) Nut Foam Seal Idler Pulley Wheel
  • William from South Chicago Heights, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer would heat up at startup but not stay hot for long. Took forever to dry clothes. Started smelling a very slight gas leak about a week before the problem started. I suspect the coils have been going lame for quite some time. The dryer heats up like it was new.
Downloaded a schematic of the dryer controls. Watched a UTUBE video of how to remove the front panel of a Maytag Performa dryer. It was pretty easy. Consulted your website and found out that bad coils are typical of the symptoms 46% of the time. I have bought parts from you before and happy with results.
Parts Used:
M Series New Style Coil Kit
  • dan from Orinda, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Plastics broke on inside of "Start" knob
Pushed new knob on starter shaft.
Parts Used:
Selector Knob with Clip
  • Peter from Mercerville, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
flame out
easy as pie !
Parts Used:
M Series New Style Coil Kit
  • john from glen head, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Loud noise
With the help of doityourself on the internet. great instructions
Parts Used:
Duct Felt Seal Front Drum Bearing Drum Bearing Slide - White (Sold individually)
  • Mary from Enterprise, AL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
I broke the handle on the dryer door.
All that was needed when I got the new handle from Fed-ex, was simply to line-up the clips with the holes in the door and push in till everything snapped in place. It was very easy. It took longer to open the package than to attach the handle.
Parts Used:
Door Handle - White
  • Donald from Central Islip, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
selector knob was striped out
Just took the old knob off and put the new knob on. It was a snap. Thanks you very much
Parts Used:
Selector Knob with Clip
  • JEAN from POPLAR GROVE, AR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broken dryer door handle
Handle was the exact replacement slipped it into the handle slots and pushed in to lock in place.
Parts Used:
Door Handle - White
  • Craig from Lee Center, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
dryer making terrible noise
watched the repair video first and it was very easy. took out screw in door to release top of dryer. removed top of dryer took out two screws holding the front panel to the side panels. removed old front drum bearing off the door replaced it with new one put it all back together. VERY VERY EASY. No repair man needed. I was impressed i could do it myself and saved tons of money not having to buy a new dryer.
Parts Used:
Drum Bearing Slide - Green (Sold individually) Duct Felt Seal Front Drum Bearing Drum Bearing Slide - White (Sold individually)
  • Dolores from Mount Washington, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer made a '' thumping noise'' when running
followed what the repair video showed , step by step and replaced the drive belt on the drum.same with the front drum bearing and slides . if you watch the videos it will be no problem.took about 30 minutes total .
Parts Used:
Drum Bearing Slide - Green (Sold individually) Drive Belt Front Drum Bearing Drum Bearing Slide - White (Sold individually)
  • Thomas from Pittsburgh, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
on/off knob cracked and would not turn on the dryer
put the new knob on and pushed it inward !! simple repair..PartSelect is a great company to do business with and very quick shipping, and great prices too. thank you so much.Brad S.
Parts Used:
Selector Knob with Clip
  • bradley from noble, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the DBXR453GT2WW
781 - 795 of 989
Back to Top