CYG4000AWW Magic Chef Dryer - Instructions

noticed that male half was in good working order, so I just snapped in the new female half; without any tools. easy repair!

easy as pie !

Followed troubleshooting steps. Checked thermal fuse (shorted)- OK. Checked igniter (about 70 ohms) - OK. checked flame sensor - (open) BAD (should read shorted). This part is normally shorted then opens when the igniter gets hot causing it to open and thus turns on the gas flow. An open flame sensor does not permit the igniter to turn on.

the video was very helpful

Watched how-to video provided on PartSelect website. Most time was spent cleaning out the cabinet of lint and other debris. I found over 5 bucks in loose change! I Found pulling the belt over the motor pulley to be the trickiest. Note: my dryer will be 30 years old come this September. I wonder how many more years I'll get out of it!

video describing repair very helpful. just folling it made the repair easy

Can't stop laughing about the mistake I almost made, before I even looked on internet I called Sears and scheduled a repair appointment, $80.00 just to have someone come out and tell me what my problem was not to repair it but to tell me whats wrong. And I told them the belt had broken I heard it when it snapped. Long story short version I found your website and entered appliance information, found part for $15.00 but also found on-site video clearly making the needed repair. Clear step by step instructions taking only 8 minutes looked very easy so I took a chance ordered the part two days later part arrived so I went into basement armed with laptop and tools. MAN it was easy.... too easy ....worked out fine video was spot on. Thanks you guys are a great company

removed front cover and turned unit on, igniter would glow red but burner would not start. ordered m series new style coil kit and installed. turned unit on and igniter came on and burner started right away. all thanks to parts select trouble shooting guide.

Thanks to Parts select it saved me hundreds of dollars. I dont know the exact age of my dryer as it was here when I bought the house. It stopped working and I thought, well here goes a few hundred dollars. I looked on line for possible fixes and found Parts select "thank goodness". There was discriptions and a video on how to fix a hight limit switch. I bought the parts was about 36 dollars with shipping, watched the video and fixed it in 15-30 minutes. simple, thanks again for having an awsome site. Dennis Pudoka, FL.

Opened the lid from the front. Took the high limit switch and bracket off. Removed the screw holding the element connection to the dryer out. This let the bracket holding the thermal switch come up. Being careful not to let the thermal switch fall out, removed it and replace it with the new thermal switch. hooked the two wires back on to it. Put the bracked on and pushed down, replaced the screw. I also replaced the high limit switch, put it back on and connected the two wires to it. Closed lid and tested.

when I see its no gas flame, i deduct the flame sensor and the electric coils not fuction, I order tru partselect and that take me like 30 min. to remplaced those parts.

Dryer was making a noise upon starting and periodically in each cycle. My husband took off the front panel and discovered the blower wheel was breaking apart. I went online and found this site, ordered, and it arrived a couple of days later. Very easily installed with the aid of a rubber mallet to push it firmly against the connecter point in the dryer.

The project was rather simple and saved the price of a new dryer! After lifting the dryer top the most difficult job was replacing the lower thermostat. It was in a relatively tight area that my hand did not fit into easily. The actual time spent on the repair was 35 to 40 minutes.

From the description of the symptoms on the site and what part fixes those symptoms I was able to determine what part I needed. The video was very easy to follow and understand it was very helpful. Hands down the best parts website I’ve ever come across.

Used the putty knife to pry open the front of the top cover. Removed the retaining screws securing front cover to each side. Lifted front panel off bottom hooks and holding drum, removed front cover. used wood block to hold drum in place. removed broken belt and belt tension spring. Keeping the rubber side of the belt against the drum, threaded belt through the tension spring onto the drive motor flywheel. Tilted dryer backwards to hold drum in place while removing wood block. Assembled front and top in reverse order. Used pressure to secure top to spring clips.