CWE600 Maytag Wall Oven - Instructions

sorry, son did job. It went like a charm. Easy, quick, and works great.Thanks

Replaced oven gasket and both oven hinges. Repairs did not work. Oven door is actually worst. Do not waste your time replacing the oven hinges unless they are actually broken. When to Ace hardware and bought a package of 3 super magnets for about $10. Practice placing the magnets on metal strip on outside of the actual oven vs the oven door. This metal strip is not galvanized for which the oven cleaning latch goes through. Appeared to solve the problem. I then used epoxy glue to insure the super magnets would permanently stay in place. These are dangerous magnets that must be kept away from children and pets. You will spend more time separating these magnets from each other than gluing them in place. This part I will let you figure out but the only way to separate the 3 magnets from each other is the slide them, one at a time, from each other. Now I am awaiting 4 to 6 hours for the epoxy to cure. Best of luck. Jeff

Unlike many here, the oven door closed enough to come up to temperature quickly and I could not feel any heat escaping. The oven worked fine but the light stayed on because the door just wasn't snug enough. I watched the great how-to video and ordered the hinges. They arrived in two or three days! I set up a work space, cued up the video again and the new hinges were installed in just a few minutes! But the door would not close enough to turn the light off! I did some more googling around and found the magnet trick! I just happened to have the perfect size magnet from a broken souvenir magnet! and now the light stays off! I stuck the magnet (about the size of a nickel) inside the door opposite the light button. This won't help if you have serious problems with the oven door, but it works if the only problem is the light!

Removed the door by unscrewing two screws holding it to the springs. Then I placed the door face down on a counter top. I removed the screws from each layer of the door and turned each layer over and laid it beside the door. Took care to support glass so it did not fall out and break. When I got to the layer where the seal was, I removed the old seal and replaced it with the new one. Then, I replaced each layer in reverse order. You have to be careful when replacing the layer that goes over the seal that the seal remains in the right place. It has a tendency to slip out of place, so check it before tightening screws. To place the door back on the spring loaded handles, prop the handles open a ways with screw driver handles. This provides a gap so that the door will slip on easily

I followed the online video at Jennair.com. The repair was easy and I saved quite a bit of money. I was quoted a price of $534.00 to replace the door hinges, I did it for $96.00 including overnight shipping chargers. I am a very happy lady.

We found the youtube video created by partselect.com and followed it. We took the door apart, cleaned the inside, removed the old hinges and replaced them with the new ones. Now the door works perfectly!

I watched the youtube video that was provided by this website on my computer while doing this repair step by step. It was a snap!

Make sure to insert a solid screw/nail/metal rod approx. 2" long, into the hole in the original hinge (doing so will preclude the hinge from "slamming closed" against the oven opening frame; plus, it holds the hinges in an offset position which makes it easier to just slide the door upward and off the hinges.) NOTE: the replacement hinge will come with a retaining pin already in place that "holds" the hinge door shaft at about a 45% angle to the spring assembly. DO NOT REMOVE THE PIN until AFTER the door is remounted on the hinge. As mentioned, just grasp the door sides and lift the door upward to clear the hinges shafts. With the retaining screw/nail/rod still inserted, the hinges are easily managed. with the door removed, two screws each hinge will be exposed. they will are easily removed. after they are removed, one will be able to manipulate to remove the hinges assemblies from the oven body (no need to remove any other oven parts). After the old hinges are removed, just install the replacement hinges into the mounting cavities and secure the hinge mounting screws (two each hinge). Slide the door on to the two hinge shafts and remove the two retaining pins. Attempt to close the door. if the door does not fit properly (too high usually), then open the door enough to reinsert the retaining pins. Remove the door and adjust the two metal screws at the very tip of the hinge door shaft to get the door to fit properly (usually you will have to turn the screw in-I had to). Reinstall the door, remove the pins, and check the fitting, making sure the door fits properly. You are done! I needed a pair of vise grips to remove the broken piece of the door shaft that had broken off in the door mounting cavity.