Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CWE5800ACS > Instructions

CWE5800ACS Maytag Wall Oven - Instructions

All installation instructions for CWE5800ACS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the wall oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CWE5800ACS
61-75 of 204
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Lower bake element would not heat.

  • Customer: Janice from SOUTHFIELD, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Removed two screws. Gently pulled old element away from back of oven, exposing two wires. Disconnected the element from wires by pulling the ends apart with hands. Reconnected the wires with new element. LESS THAN FIVE MINUTES! Saved about a hundred bucks!. (Demo on You Tube.)

The oven heating element burned out and would no longer heat.

  • Customer: Gary L. from SUN CITY, AZ
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
It was very simple. First thing I did was to go online to youtube and type in the kind of repair I intended to do. There were several short videos showing you how to do the replacement.It was easy and took about 30 to 45 minutes. First thing is shut off the power to the oven. ( Very important). You then need to take out two screws that hold the element in place. At this point, just pull the element toward the front of the oven. You will see some insulation at the hole where the wires come out. Slowly work the element forward until you see the fasteners on the wires ( two wires).Disconnect the fasteners and throw the old element out and put the new one in the oven.Connect the element, push everything back into the hole and screw the element to the back wall. You're done ! I had two wall ovens to fix.

Oven temperature fluctuates

  • Customer: Larry from SOLON, IA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.

Blown element

  • Customer: Kathy from SANDYSTON, NJ
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Very easy. Didn't have to replace whole unit

original fixture required bulb - this fixture (all-in-one) was great

  • Customer: wesley from ODENVILLE, AL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Pulled range out from cabinet-wall to get to back side, everthing was clearly exposed tlhen. Just a matter of installing new fixture, putting back on, reconnected power source - put range back in proper place.

Oven would not heat

  • Customer: Ralph from Nicholasville, KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and oven works like new.

Thermostat bulb was hanging loose

  • Customer: Willi from Old Saybrook, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 2 of 5 people found this instruction helpful
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

Oven not heating to desired temp

  • Customer: Raymond from Ridgecrest, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 5 people found this instruction helpful
Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cable adapter that came with the new sensor was needed in my case.

burned out element

  • Customer: Richard from Highland Village, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
This was an easy thing to do. Take the two screws off the back, pull the wires out, pull off the connectors, get the new element, replace the connectors, make a hole in the insulation, fish the wires back behind the insulation, screw the mounting screws and turn it on. The only thing I did extra is clean the bottom of the oven because with the element out, it's easy to do.

Lower element was broken.

  • Customer: Daniel from Wilmington, DE
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Awesome, just awesome, you guys are great and I will use you again and again.

Oven Over Heating

  • Customer: Steve from New Albany, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.

After doing an oven self clean cycle, oven temp couldnt be set correctly, heat element was warm,not hot

  • Customer: Philip from Winter Haven, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!

Heating element burned out

  • Customer: Ellis from West Valley City, UT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Found the model number, called the local parts store, they quoted $60 + $10 shipping because it was a warehouse order or something. So I came hear and got it for $42 + $7 shipping!

Turned off power, unscrewed the element, disconnected the clips from broken element, connected them to the new, screwed in the new element, and it was done

the element was burned!

  • Customer: Terry from Arlington, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
unscrew the old ones and replaced the new one - easy as that! Savings of over $300.00 if I need to buy a new one! Thanks for the speedy service after I ordered it.

oven element not wrk'n

  • Customer: Debbie from MT.VERNON, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Simply removed old element,2 screws,clean'd oven b/4 install'n new one,reconnect'd 2 wires,2 screws & yea oven wrks again. My husband was very happy as the oven is 34 yrs old,I just copied the model #,went 2 u'r web site,& we r very happy campers,so thank you very much.
Debbie A. Martin
All Instructions for the CWE5800ACS
61-75 of 204