CSP2761AN1 Whirlpool Dryer - Instructions

Remove lower bottom cover (two screws on bottom) with screw driver. Remove old radiant flame sensor from left side of tube with ignior by using socket wretch. Remove wires with needle nose pliers. Put new part in: put wires back on, insert part's lower tab into the tube ( there is a small slot) use socket wrench to tighten screw at top. Put bottom front panel back on and screw back in.

I removed the front lower panel and could access the parts easily. This model of dryer was a little tricky as to what needed to be removed to access the parts. It was easy to take off the flame sensor and the therminal gas valve and replace. I watched your video on changing these parts but it didn't help much as the model in your video was newer and the parts were not in the same location on my dryer. the top on my dryer could not be popped up it was held by screws accessed by working from the bottom panels up. It turned out I only needed to take off the bottom kick panel to replace the parts it needed. The dryer works fine and the information,you provided on your website about what parts cause this problem most of the time on this dryer helped me to order the correct parts.

This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

1. Disconnect power cord and remove flexible duct. 2. Tilt dryer back and lean against wall, using folded towel to prevent wall damage. 3. Remove front/bottom panel - 4 screws on front/bottom of dryer. 4. Make alignment marks on internal vent duct where it attaches to vent bottom duct housing. Remove internal vent duct screw (towards front/top of duct) and slide vent duct out back of dryer (duct has to be removed to remove back panel) 5. Remove top panel (4 screws on back/top). 6. Remove AC power terminal block from back panel, disconnecting wire that restricts free movement of terminal block. Remove power cord from terminal block (3 nuts). Remove back panel (many screws). 7. From rear of dryer, gain access to idler pulley spring arm. Carefully note how belt routes around motor pulley and idler pulley (maybe record an image). Release belt from idler pulley. 8. Remove idler pulley triangle retainer (if still on pulley shaft) and remove old pulley. 9. Thoroughly vacuum lint and dust from all areas of dryer, internal duct, flexible duct and duct in wall (as far as possible) while dryer is in disassembled state. 10. Thoroughly clean idler pulley shaft of deposits with cloth. If desired, add very small amount of Park Tools Polylube 1000 to the cleaned shaft. 11. Install new washer, idler pulley and triangle retainer to shaft. 12. Re-route belt around pulley in original orientation. 13. Reassemble rear panel to dryer, terminal block to rear panel, and power cable and internal wire to terminal block. 14. Reassemble top cover to dryer. 15. Insert internal duct back into front vent duct, aligning guide marks, and secure with the one screw. 16. Plug unit in and briefly test, then unplug. 17. Again, tilt dryer against wall and reinstall front/bottom panel and screws. 18. Install flexible duct, plug in power cord and position unit for operation.

The gas would light briefly then go out so the clothes were never heated. I googled the problem and found your website and read a few blogs describing the problem, ordered the coils, popped them in and presto it worked.

I read the instructions on the internet. It told me what to trouble shoot first. The switch on the door then the thermo fuse and after that the thermostat. The off on switch on the door checked ok but the thermo fuse didn't when I followed the instructions on the internet. The thermostat did check ok. When I installed the new thermo fuse the dryer started like always before. I was pretty proud of myself for saving a hundred dollars or more. Thank you for the hlpful instructions.Larry

I must say what really made this install/replacement easy is the YouTube video link that was included with the belt replacement part. Once I saw the video (which showed my exact model dryer) it was a piece of cake! There was some work involved but once I got all the screws removed and took the shell off, installing the belt was a cake walk after watching the video. Many thanks!

I replaced gas coils which in my case came as a set and that did the trick.

I started by taking the front of my dryer off and cleaned it out. Next i ran the dryer and watched the flame starter circut. The starter circut would work once and then not for a long time but i could see it was tring to light because the iginiter would glow white hot. I then searched online for my model number and found the part select web site. In a few minutes I found a dryer fault description that best fit what my dryer was doing. The part select site should me three parts it might be. I read about what the three parts did on the parts select site. Then by using the process of elimination, with the knowledge I had just learned, I narrowed my suspect parts down to one. The coil for the gas valve must be the problem. So I got my ohm meter and measured the coil resistance and I found that when the coil was room temp it had resistance. But it would get hot after one heat cycle and it would open up therefore causing the gas valve not to open......no heat! I ordered the part and it came in two days!!!! All fixed!

It snapped right in. Works perfect.

I watched the video and after that made the repair, it was very easy and the video was a really big help. From start to finish it took me no longer than 10 minutes.

My experience was a positive one. I called the company and read the part number from kitchen aid and the technician on the other line knew exactly what i needed. He gave me the part number and the price and took care of my order. Within 3-5 days i received my part. I am really happy with this company and i will call again when one of my applicances is not working.

Thank you for your part service. It saved me about $ 200.00 dollars by Sears not coming out to repair a simple problem.

after watching the instuctional installation video, it real took about 25 to 30 mins to install the new belt. The video was perfact and made the installation so easy..

I have a whirlpool gas dryer. My dryer all of a sudden would not heat up. I diagnosed the problem and discovered that it would light (using the peep hole in the front) when the dryer was cold, but once warm, the flame would go out. I bought a cheap multimeter and tested all the themostats on the back of the unit after removing the back panel. All the thermomstats checked out except the cycling thermostat which should no signal through one of the connections (purple wires). I ordered a new thermo and replaced the old one but it didn't fix the problem. Seems that there isn't a current between the purple connections.... Since the flame did light when the unit was cold I figured it wasn't the ignitor so it was either the flame sensor or the coils. I took the top and front panels off (alot easier than I thought; see videos) and checked the flame sensor with my multimeter. It was fine. Only thing left was the coils, so I ordered a set. IF YOU NEED COILS, SAVE YOURSELF MONEY AND ORDER THE PAIR. YOU GET BOTH COILS FOR < HALF THE PRICE IF ORDERING INDIVIDUALLY. Replacing the coils was rather easy. You will need to prop up the drum with something to keep it from impeding your screwdriver. A stubby philips really helped here. Also, since the gas valves are closed when there is no power, there is no need to disconnect the gas line and fuss about a gas leak (This really saved time). Once the two screws for the coil plate were out of the way, the coils simply slide off the valves and unplug easily. NOTE: Make sure you line up the one new coil with plate when you put it back together. It has a little tab that fits into the plate. All-in-all it took about 30-60 minutes to do. If I were to do it again it would probably take 15 minutes. Pretty easy job for a do-it-yourselfer with only basic tools.