Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven wouldn’t get up to temperature
I removed the sensor from inside the oven with a 1/4” nut driver, pulled the sensor out slowly and then took the connection apart and found out that the connector was different, I cut the connector off of the oven side and then cut the connector off of the new sensor and wired it together. I am still trying to find the ceramic nuts. My oven is working for now. Very easy fix, just wish there were ceramic wire nuts with the new sensor
Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....
Took back off the oven unscrewed the time control scaped old one off and put new one on. Than I put it back together again. What a great place to shop!!!
Broil worked on the stove, however in bake mode, the oven did not make temperature. Turned off the stove, unscrewed and inspected coil. I noted there was a section of the coil that had a "corroded" appearance. (it was evidence of the coil being burned out). Checked with a ($9.00) voltmeter, showed infinite resistance. Found the original envelop for the stove taped to the back of the oven from 1973. It has wiring diagram with schematic and noted the coil was 3000 W, 19 ohms.
Bottom Line found comparable replacement online and tested resistance, measure dimensions of the old coil, matched with Watt rating, replaced, tested installed and works great, Oven has been in use for a couple weeks now. New stove would have been around $500.00. Not to mention some remodel work, as the house is old and stove is a built in.
Coil was $60.00 and should buy the time I need until I remodel the entire kitchen.
my mother blew up the old element. she wanted to tie it for 8 minutes but set it to 800 deg. f. lol:)
searched on the computer for the name and part number that was damaged, found that it was the bake element so i ordered it with part select.com. when it arriver three days later (as expected) i disconnected the gas and electric to the range and simply removed the old element with a phillips screw driver. installed the new element, hooked the gas and electric back up and began cooking again...
Simply took oven out of wall, removed back plate, unplugged old sensor, went in the front and unscrewed old sensor, put in new sensor, went in back and plugged in new sensor, put on back plate, push oven in wall. Turn on power
1. Turn off power to the electric oven 2. Removed the two screws in the top side of the oven that hold it into the cabinet. 3. Made a support to set the oven on once you remove it from the wall. Or set it on the floor. You will need help this is not a one person job. 4. Used a Philips head screw drive removed the back of the oven panel. I did not have to remove the whole thing just took out half the screws and the electrical plug for the temperature sensor is right on the edge. 5. Unplugged sensor 6. Took out the two screw on the inside of the oven that holds the thermal sensor in place. Pulled it out the front. 7. Side the new thermal sensor in place replace the screws. 8. Pull the plug out and plug it back in. Check and push the insulation back in place where the thermal sensor. 9. Replace the back and replace the screws. 10. Slide oven back into the wall. 11. Replace the two screws that hold the oven in place in the frame. 12. Turn power back on Check the temperature
While removing burned out light bulb, the glass cover fell to the floor of the oven and broke!!
Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)
Controller fails to hold a constant heating element tempature
The replacement of this part is simple enough, out with the old, in with the new. At issue here is the way the controller fails. The heating element goes to the highest temperature. The original controller on this Kenmore oven failed after about two years and the first replacement that I got from you lasted about a year and a half. The defective controllers seem to be working properly once the controller has been turned off and then restarted, but the frequency of failure increases with time until you hardly dare to step away from the oven. This controller should open on failyor, not close.