CSH24GRTAAA Hotpoint Refrigerator - Instructions

Removed ice buscket from freezer, removed 4 screws holding front cover on, set aside old ice bucket, set new ice bucket in place and reinstalled screws, putback in freezer, done. Maybee ten minutes.

shimed the door up to its proper level. removed plastic cam from bottom of door with a socket disconnected the water line fitting and clamp. with a nut driver removed the hinge assy from cabinet being careful i sled the hinge assy off the plastic water line being sure not to kink the line, sled the new hinge assy back on the water line and mounted the new hinge assy to the cabinet and connected the water line back up and turned on the water and checked for leaks, all went well. place the bottom grill cover back on.

I pulled the refrigerator away from the wall. I turned the water supply valve off. With a nut driver I removed the screws holding the flexible cover on the back of the refrigerator, and set it aside. Next, again using the nut driver, I removed the screw form the clamp holding the copper tubing to the back of the refrigerator. Using a 1/2 inch open end wrench I took the copper tube off the water valve. Then, using the nut driver I removed the screw which holds the valve in place. I then unplugged the electrical wiring,and removed the two flexible tubes. I pulled the compression nuts from the flexible tubes, and inserted them into the new water valve, re-connecter the electrical wiring plugs, mounted the new valve to the refrigerator, reconnected the copper tubing to the new valve, turned the water supply valve on to be sure there was no leaks, secured the copper tubing to the refrigerator replaced the flexible cover, and then moved the refrigerator back in it's original position.

My wife removed the drawer and the glass shelf. Unscrewed the broken rail and screwed in the new one. Replaced the glass shelf and the drawer and she was done.

Removed the knob, covers and unplugged the old and installed the new control. Piece of cake.

I turned off the power and water supply to the refrigerator Pulled fridge out,found leak at water valve. Removed valve,got on internet found partsselect and was able to match it up by model and picture. It was a lot easier than I expected it to be, thanks to the pictures. I ordered the part on Sunday night and got it Tuesday. Unbelievable. Put it in in about 10 minutes and drinking cold water with ice cubes again. The fridge wasnt down long enough to acually run out of ice. the fridge is 12 years old and keeping its maintenance low is a priority. If I had to hire a repair service we would probably thought seriously about replacing it.

Followed directions in your video. Very helpful. Be certain to pay strict attention to how old part is removed. Had a little trouble replacing door on lower pin/hinge. Helps to have a little assistance. Good suggestion from another customer: get the kit.

Removal was easy. The problem was that the old hinge had screws approximately 3/4 inch apart. The new hinge assembly had screws 1 inch apart. The threaded backing plate matched the 3/4 inch spaced old hinge but would not line up with the new one. There was a hole in the refrigerator frame but no way to hold the screw from the back. I had to fine a bolt and nut that would fir and still be heavy enough to hold the weight of the door. This repair took place at my cabin--miles from any hardware store. I found a long enough bolt and nut but it was a little too big for the hole in the hinge. I had to drill the hole in the hinge out so it would fit. Trying to reach the back of the bolt with a nut was a problem. I used tape wrapped backwards on my finger to hold the nut and then reached around to start the bolt into the nut. It too a few tries but I finally got it. Bottom screw was not a problem. It took about an hour and a half to fix the door but it works fine now.

order new augerand ice bucked changed face plate 4 screws now have good clean ice

The video on the GE site was great. Showed step by step instructions on how to remove the old ice maker and install the new one. Also helpful was the detail on the water chute which needed to be moved from the old ice make to the new one. Saved hundreds of dollars by not having to have a repairman do this work for me.

Pop off the Plastic cover over the Ice maker panel in the door.Remove the 4 Phillips screws. Pop off the rubber Switch pad in the back. Open the Freezer door to disconnect the power and stop water flow. Pull the assembly forward watching the water spout pull through the gap in the lever. Disconnect the white connector by gently pulling it up, it assembles only 1 way. Pull the 2 switch knobs off. With the assembly loose. there are 2 Phillips screws that need to be removed. The cover comes up, and the pc control board slides out. Insert the new control board and reverse the procedure. Be a little careful when inserting the assembly so that the water spout comes through the gap in the lever.