I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and replaced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.
Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.
Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!
Thanks to previous posters, this seemed to be an igniter issue, and I found the idea of swapping the broiler igniter for the bottom one particularly good - I knew exactly what part was broken and how easy/hard the job would be prior to ordering. The part used snap in electric components, so the only work was in removing and re-installing the parts. Working in the oven was by FAR the most difficult part of the entire process.
Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.
Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith
gas burners would not light with electric ignighters
using the diagram shown on line Looked up the ignition module and ordered it by phone. Received it the next day and installed it within the hour. Previously I had called the repairman and he said it would be a couple of weeks before he could look at it and a service call was $75 plus parts..I fixed it for the cost of the module $34. I am very satisfied.
Igniter was not getting hot enough to allow burner to come on.
took out two screws that held Igniter to burner, unbluged wires from behind and pulled them out to the front of over, replaced with new one, solved the problem of the burner not coming on,,,,
My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!
broke the igniter in the oven before I even got the oven installed
ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.
Oven would not start, ignitor was not doing anything
My wife said the oven would not heat up, I took a look at it and determined it was not igniting. I figured there was an electric spark like my BBQ. When I took the pan out of the bottom of the oven I saw that it did not look like anything I had seen before. I looked it up online and found out it had a glow ignitor that just heats up and then ignites the gas. Mine wasn't doing anything so I removed it, got a part number off of it an plugged that into this site. It came up with the part, i ordered it, put it in and started it up. probably took about 45 minutes total including taking it out and then replacing it. Really easy and the oven is now working fine. Figured it would have been a couple hundred dollars to have someone come to the house and fix it, I did it myself for less than 50. Thanks Partselect.
Timer quit working and starting making arcing sounds
This repair was very simple. First I UNPLUGGED the stove. Then I removed the 6 screws on the top portion of the back panel. Then I removed the knobs from the front of the stove. Then I removed the 2 screws holding on the front glass covering the clock/timer. I then drew a diagram of the wire colors and the corresponding numbers on the old timer block. Then I removed the 6 wires from the old timer. I then pushed in on the 4 black holders that secure the clock/timer to the chassis. The clock/timer pushes out from the rear to the front. Going back together, just push the new clock/timer into the hole until the holders snap in place. I then found the corresponding numbers on the new clock/timer block and put on the respective wire colors. I then put the front glass back on, then the knobs, then the back panel. Plug it in and you are golden. It couldn't be easier. It took all of about 15 minutes.
part was by the brolier drawer inside under stove removed 2 screws on cover/ part was attached to cover removed module line 1-2 fit/ had to use supplied disconects crimped on 4 burner wire leads/taped around module w/ elec. tape put back 2 screws finished. works now.