CRE8700BDE Maytag Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Damaged the oven lamp socket while removing a broken bulb.
Upon receiving the replacement part, I noted that the socket was held in place by simple expanding tabs. TURN OFF POWER TO THE OVEN. Using a right angle pick or similar tool, bend the tabs inward on the existing socket and remove. Disconnect the white, black and green wires. Note which tab is the green tab. Attach the wires to the new socket. Push the new socket into place, aligning the key bump on the socket with he slot in the oven wall opening. Install bulb and diffuser.
Parts Used:
-
Ronald from Dover, DE
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Range had an F-2 code on the control panel
I removed the old thermostat and replaced it with the new one using the supplied wiring adapter for my model of range. Parts Select made this an easy project. Thanksyou
Parts Used:
-
Greg from Frederick, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Element caught fire and melted
two philips head screws and pull straight out about 6 inches unfasten wire connectors. Be careful not to let insulation catch fire when you reconnect the two slip on connectors. Put the two screws back in and you are done
Parts Used:
-
Maurice from Joshua Tree, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Cartridge wire burned out
I was unable to remove the screw which held the electrical element.. so I took the new surface burner receptacle and removed the metal part, and used the old one and put in the new one in the old metal part and rewired, and it is like new.. now I need to do another one.
Parts Used:
-
Robert from San Francisco, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Oven would overheat
Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.
Parts Used:
-
MARK from roseville, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken plastic knob
-
Judy from McKinney, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Replace bake element
Remove two Phillips head screws , detach element , replace with new one. Very simple
Parts Used:
-
Patrick from Scituate, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
My bake element burned up and broke
I ordered the part on a Monday morning and I had it on Tuesday. (I used regular shipping) Took out the oven racks and unscrewed the element. I pulled out the element about 4 inches and disconnected the wires, and removed the element. I made sure the wires were not burned and that the connectors looked good. They did. I simply connected the wires to the new element and screwed it back in place.
Parts Used:
-
John from Milford, DE
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burnt out bake element
My husband did it and was very easy. Has been done before too. Very fast service from you also. Will order again if we need to.
Parts Used:
-
Janet from Hillsboro, ND
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
When We Turned On The Oven The Temp. Reading Went Up To 425 And Beeped By No Heat
Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call
Parts Used:
-
DAVID from Cape Coral, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
change oven sensor
-
Lloyd from Eau Claire, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
I had a power serge and it burned the Plug at the termial block and melted a few wire.
After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.
Parts Used:
-
Robin from Vanderbilt, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Missing Oven Rack
I think the installation instructions are fairly self explanatory. This is the second item I've ordered from Parts Select and I'm thrilled with their service. The items are always less expensive than other sites and they deliver what they promise. I would highly recommend them.
Parts Used:
-
Janine from Hatfield, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Oven was not working, couldn't bake
Amazingly simple. Removed 2 screws, pulled off 2 wire terminals, removed broken element. Re-attached wire terminals, installed screws.......baked some cookies to reward myself. lol Actually, my girlfriend replaced this part. I just talked her through it. Thanks Partselect. I wasn't able to save you any cookies though.
Parts Used:
-
Bryan from Midland, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!