Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CMV1000ADW > Instructions

CMV1000ADW Maytag Microwave - Instructions

All installation instructions for CMV1000ADW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CMV1000ADW
16-30 of 42
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

microwave handle was completely broken off

  • Customer: Ruth from New Bloomfield, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Found info on how to replace handle here. Couldn't have done it without that information! We popped out the black trim on the inside of the door and removed the spring to access the bottom screw. From there it was pretty much easy to see where ever thing fit. Had difficulty getting the tabs clipped in the front of the door.

Broken Inner and Outer handle

  • Customer: David from Fredericksburg, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
1. Open Door
2. Use Putty Knife and and carefully separate outer door frame from inner door frame
by sliding the putty knife all the way around the frame from the inside
3. Remove the old broken handle. You should use a pointy nose pliers to take hold of the
handle screws once you have then loose...
4. Install new handle, Make sure it is seated flush in the door frame, then tighten with
two screws (use the pointy nose pliers to get them started . .very tight space to work in)
5. Snap on outer frame.
6. Your done!
Dave

Handle broken

  • Customer: Tom from Brecksville, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
remove inner door frame,remove screws holding inner and outer handles reuse inner handle,replace outer handle as needed reinstall inner door frame.

Followed instructions from internet

  • Customer: Effie from Hilltop Lakes, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
My son took the door sealer off. It just pulls off easily. Then with screw driver took out the screws and put on the outer part of handle and replaced the screws and bracket. Took less than 30 minutes after we found how to do it.

microwave door handle broke

  • Customer: Bonnie G from Port Townsend, WA
  • Difficulty: Really Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I received the door handle in 2 pieces along with one screw to put the two together. 3 days later the 2 screws to attach the handle to the microwave door showed up so I could finally put the handle on. I was amazed that I had to purchase each piece separately and that they pieces were shipped in two deliveries.

Handle broke from our over the range microwave oven

  • Customer: Michael from Chaska, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
removed screws from the old handle (this took the longest amount of time - 5 minutes, and required a needle nose pliers and a screw driver). Replacing the handle took 2 minutes to screw the handle to the door. Very easy!!

Handle broke off original microwave door

  • Customer: Joseph from Bridgewater, NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Separated the inside panel on the microwave door, removed the screws from the old door handle and utilized them to install new door handle. Access to the screws was a little tight thus the "a bit difficult" rating.

Replaced broken door handle

  • Customer: David from Parma, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
Removed the door from the oven by lifting and unhooking from appliance.
With a small putty knife remove the snap-in ring from the inner door.This will expose the screws that hold the handle.
Replace then put everything back in reverse order.

Roller/guide was broken

  • Customer: Connie from St Charles, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
Put in the new roller/guide

Burnt Out Light Bulb Replacement

  • Customer: alfred from summerville, SC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 29 people found this instruction helpful
Open compartment, installed bulb, closed compartment

locking pen came out of microwave

  • Customer: Jeanette from Honey Creek, IA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Piece of cake once you order the right part!

Replacement of hood light bulbs

  • Customer: Jerry from Pine, CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug the microwave. Then remove the six screws that hold the lower panel which has the light bulb cover and a couple of vent filters. The light bulb sockets are on a fixture that is connected by a quick connect electrical connector. Disconnect that and the whole panel is free to access the bulbs. My bulbs were very fragile and trying to twist them out resulted in the glass twisitng loose with the base still in the sockets. I needed to use a needle nose pliers to remove the bases and then I replaced the bulbs and put every thing back together

Door handle to Microwave broke off.

  • Customer: William from Chicago, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair guy quoted $85 plus parts. It looked like there was no way for me to access the screws and change out the handle mysself, but after looking at the blow-up diagram on the Parts-Select web site I saw that the piece covering the screws was meant to be gently popped off at several specific points, which I could plainly see on the diagram. With this knowledge I was able to replace the handle at cost, completely omitting the $85 for a repairman. Thanks Parts-Select!

Handle broke off.

  • Customer: Charles from Nokomis, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the instructions and it went from "this is impossible" to "this is a piece of cake". Thanks.

Outer plastic handle failed[female screw fitting crackrd and would not hold screw. Handle would not tighten down.

  • Customer: charles from Elkader, IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered new outer plastic handle and tightened the handle.
All Instructions for the CMV1000ADW
16-30 of 42