Models > CLZ8560ADB > Instructions

CLZ8560ADB Magic Chef Cooktop - Instructions

All Instructions for the CLZ8560ADB
1 - 15 of 19
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The grommets came apart metal from rubber.
I replaced the broken grommets with the new ones. I purchased 8 so I would have back ups because I did not feel the new one would last either. I think they cost TOO MUCH but I could not haggle for price.
Parts Used:
Rubber Grommet
  • Frank from Pierce, ID
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
23 of 27 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
range top loose, grommets missing
very easy to push each grommet into range top holes
Parts Used:
Rubber Grommet
  • joseph from wildomar, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
12 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner would not light
saw burner tube was completely rusted at end and would not line up with burner. decided to go ahead and replace all three tubes. was easy to install, able to get a good cleaning job on unit in the process. works fine, wife is happy and that is what matters in a motorhome.
Parts Used:
Flashtube Extention - Front
  • Albert from Clewiston, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
11 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
missing gromet
Pushed into hole by hand, really simple
Parts Used:
Rubber Grommet
  • Hal from National City, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Inside Of Knob Busted Out, Would Not Turn Ignitor.
Actually too simply to list as diy job. Merely remove old knob and push new one onto spindle.
Parts Used:
Ignition Knob
  • DAVID from SEARCY, AR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
5 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
existing grates were very worn.
Just ordered a new grate. Everyother place I talked to said the one piece grate would not fit, so I am very pleased with the service you offered.
Parts Used:
Burner Grate
  • Alta from Rexford, MT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
5 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
igniter knob for gas stove stripped out
Slip old knob off slide new knob on, be sure to align knob properly your done
Parts Used:
Ignition Knob
  • Brady from CARYVILLE, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bushings were worn out
The parts were exactly correct. The website was complete and easy to use. The reair was a snap.
Parts Used:
Grommet
  • Fred from Spring, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wouldn't ignite
Pulled knob,removed 2 screws removed wire,removed old ignitor repl. With new reversed procedure,done
Parts Used:
Burner Control Valve with Igniter
  • William from ARCHER, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Finish errosion
Replaced with new part
Parts Used:
USE WPL 2001F148-09
  • Kenneth from Lakewood, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Igniter failed
The igniter on our RV stove top failed after 4 years of operation. The repair took about 8 minutes and everything works fine.
Parts Used:
Burner Control Valve with Igniter Range Surface Burner Igniter Wire Harness
  • Paul from Niland, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knob would not turn igniter.
Simple off/on installation.
Parts Used:
Ignition Knob
  • Harvey from Lynchburg, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Lost on of the Rubber Grommet holding the stove grate
So simple would be embarrassed to give any instructions; it is so self evident.
Parts Used:
Rubber Grommet
  • Martin from Millersburg, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Front flashtube extension rusted through, ignition knob stripped, rubber grommet missing
Removed screws from igniter cover, removed and replaced fron extension tube. Removed old knob and replaced. Replaced missing grommet. Saved other extension tubes as the old ones were still serviceable.
Parts Used:
Rubber Grommet Ignition Knob Flashtube Extention - Front
  • Henry from Omaha, NE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
flashtube was burned off
put in new flashtube
Parts Used:
Flashtube Extention - Front
  • john from mount vernon, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CLZ8560ADB
1 - 15 of 19
Back to Top