CGR3765ADC Magic Chef Range - Instructions

Removed oven door, pulled oven out to acess the rear of unit. Removed two screws inside the oven that connect the ignitor to the mounting bracket. Used flashlight to find plug that is connected to the ignitor located at the rear of the oven. I could see the plug in space provided in the oven rear cover plate. Did not have to remove anything to access the plug. Unplugged connector, tied string on connector and removed ignitor from inside the oven. Tied string line on new ignitor plug and pulled the new ignitor plug to the back of the oven by pulling on the string line. Connected plug and installed screws in the mounting bracket and turned on oven. It worked fine. The hardest thing to do was pull the oven from the wall and put it back. The wife had a good opportunity to clean the crap from the floor under the oven so it was good to move it out. Easy job and so far everything is ok. I am very satified with the part

uninstalled old igniter like video showed and reinstalled new one and then tested right away thank you for your help

It was easy because the clips were already on the new door gasket. Just had to remove old door gasket and replace it with the new one. Very simple job.

New burner and igniter.....actually it was very easy to to fix

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Based on user comments it seemed like my problem was being caused by a faulty igniter. I didn't do any voltage or continuity checks like some of the other comments said, although that route was provide a definite yes or no regarding the cause. For instructions, just watch the video. They are dead on. The screws holding your igniter onto the burner assembly may be stripped so you might have to buy replacements or use spares. I replaced the factory sheet metal screws with 10-24 machine screws, nuts, and washers I had laying around the house. After reassmebly, I tested the oven and it lit right up and stayed burning until it reached temperature. My wife baked a test batch of cookies the next day and they were delicious.

Twisted and lifted off the burner, loosened in a previous repair; removed electrical wires from igniter; undid two screws holding igniter in place; rotated igniter 90 degrees and lifted it out; reversed process with new igniter.3

I ordered the igniter part and receive it the next day with standard shipping. It was very easy to intall it took about 15-20 minutes and your repairman video was excellent.

It was very easy we followed the video and it was very easy.Thank you PartsSelect!

My husband and I were prepared to go and buy a new oven... WE ARE NOT DIYers, but I looked up the model no and problem on the internet. Thank heavens I found the PartSelect site. The best part was the YouTube video!!! It was the easiest repair. For under $50 and 30 minutes our oven works like new! My friends were so impressed, they have asked for the website!!!

I followed the instructions on this website. Luckily a friend showed me where the sensor was located and from there, it was a breeze. Removed six screws on the back oven panel, removed two screws inside of the oven, took the old sensor out and put the new sensor in. Voila - works great. I can't tell you how much I appreciate Parts Select and the feedback and help from the customers. I've been out of work for almost two years and when I called my repair guy, he said it could be the computer and that would be expensive. That's when I searched on line and found Parts Select. I would have never even attempted this on my own if it weren't for you and it was so simple. Next time anything goes wrong with an appliance, I'll be contacting you first! Thank you.

Removed old gasket and replaced with new gasket'

I was a little intimadated as I hadn't tried any type of repair like this before. My oven is almost 20 years old so the ignitor was hard wired; there wasn't any plug. I wasn't able to remove the burner assembly so I had to do all my work inside the oven. I had to cut off the plug and hard wire it to the oven. It works great now. All I noticed was that the oven temperature is higher than what I set it at.

Took the old igniter out by taken some screws from the top had to remove the bottom cover underneath then had to cut one of the wire on the igniter put the new one end put the screws back in plug in the oven back iand then check to see that the oven will get hot it did the repair went well.

Removed the racks and bottom tray in the oven. Unplugged the old igniter and plugged the new one in.