Models > CG206S > Instructions

CG206S Jenn-Air Cooktop - Instructions

All Instructions for the CG206S
121 - 127 of 127
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Burner was not lighting
I removed the pan and then the burner assembly. Used a nutdriver to remove the old front burner. Replaced with the new part, tightened it on, and tested the new burner. Worked first time. Extremely easy. It took less than 5 minutes to replace.
Parts Used:
Front Burner Assembly - Black (Glossy Finish)
  • Luciano from Hollister, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Nroken Burnner knob
Slide the knob onto the shaft.
Parts Used:
Surface Burner Knob
  • William M. from Rock Hill, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Replace Grill Side with Burners because I never used the Grill
Very simple remove the Grill section and install the Burners no reworking of existing Unit is required
Parts Used:
Burner Bracket - Black Double Burner Pan - Black Rear Burner Front Burner Burner Grate - Black Screw, 8/18 x 3/8
  • Don from Scott, AR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Filter worn out, exhasut fan kept going off
Old filter allowed too much air flow causing exhaust fan to go off....installed new filter in exhaust chamber...release clip on old filter and install new filter (at an angle) in the exhaust box....clamp down clip on edge of filter and job is complete
Parts Used:
Grease Filter
  • John from Cayce, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The Burner Grates were old and bent out of alignment.
The repair was as easy as could be. We simply lifted off the old burner grates and set the new ones in their places.
Parts Used:
Burner Grate - Black
  • Carl from Fairfax, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Front burners would not light.
First, unplugged the cooktop from outlet and shut off gas. Then, removed burner assembly then located and removed existing spark module. Installed new spark module kit, reassembled burner assembly and then plugged unit into electricity and turned gas on. Was rewarded when testing burners with an instant ignition.
Parts Used:
Surface Burners Spark Module Kit
  • Jeffrey from Columbus, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
rear burner not working
removed two hexigon screws--removed old burner---placed new burner into stove socket--replaced two screws. Done in about five minutes. Most time used to fine right size socket to fit screws! Fast delivery--easy repair--AND it works!
Parts Used:
Rear Burner
  • Larry from Washington, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CG206S
121 - 127 of 127
Back to Top