CFEF370GS2 Frigidaire Range - Instructions

The repair was simple; first I removed the 2 screws from the old element and disconnected the wires and then I inserted the new element reconnected the wires and replaced the screws . The repair was easy and took less that 15 min. The oven works as good as new and I saved alot of money by doing it myself.

Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven and attached with two screws; the back of the oven will need to be removed to unplug. Reverse removal procedure and turn the power back on to the stove.

I pulled my unit out of the wall and noticed that the insulation around the top broiler element was a bit brown. Closer inspection revealed that the element had shorted somehow to the oven itself and caused the element to become non-functional. I tried measuring the resistance first, and it was within typical values for the other elements, but I decided to replace the element anyway.

I ordered from PD and the part arrived just a few days letter by regular shipping. I undid the screws holding in the element, undid the wire connectors and replaced the broken element with the new one. The element worked like a charm and I was back in business for cooking.

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

First we removed two screws under the rim of the range top to open the lid. Lifted the lid and removed the screws from the bracket that holds the elements, Be careful with the clips that hold the element in, if you break them or bend them there aren't any more! Also note which holes they were in, they are marked according to the different sizes of elements. Disconnected the wires, needed needlenose pliers to grip them...connected new element, popped it back in place, replaced bracket, closed top ...Easy peasy!!!

Repair was quite easy, as long as you have the instructions for removing the door. The screws that hold the bottom of the door to the fixed hinge are placed into the side of the hinge assembly after removal; this holds the door at a 45 degree angle for easy removal. After that, just place the door on a flat surface and dismantle the door from the inside. The inner glass is contained in a metal frame with another piece of glass; this frame comes apart easily using the clips in each side. The door assembles easily after the glass is replaced; just take your time and give yourself enough room to lay out the parts as you go. Good luck!

I called a repair place. They charged $54 to diagnose, (said it needed a new latch motor) then wanted $220 to complete the repair. I checked online prices and did it myself for about 15 minutes work and the latch motor itself ($44?).

Was necessary to uplug the range, pull it away from the wall and remove the back panel sheet metal, then 3 screws that mount the motor. Replace motor, reattach sheet metal. Plug in. Done. Ready to bake cookies.

PartsSelect serivce was AMAZING - I ordered online on Sunday afternoon, and the part arrived Tuesday with standard shipping! First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires from the old element, then replaced with new. WARNING - you MUST kill the breaker, because the element is "hot" even when it's off.

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

VERY IMPORTANT! kill the circuit breaker to the unit and/or unplugged it! 2 screws hold the ceramic glass top to the lip @ top of oven--remove them and the top can be lifted up to expose all the burner elements and wiring--remove the 2 end screws that hold the retainer bracket for the burners - then remove the 2 screws that hold the burner in question to the bracket-there's also a retainer pin that needs a bit of fussing with to completely free the burner--once totally free remove the wires from the bad unit to the good unit exactly as they are situated --install new unit onto bracket with screws and bracket back to its original location on the ceramic top-put top back down and replace both anchor screws--initiate power back to unit and yeeehahh--You just saved yourself lottsa money from repair bills!!!

FIRST I UNPLUGGED THE GLASS TOP RANGE. While locating the part on the PartSelect diagram I was also able to determine how to access the burned out element. It was very simply to remove three phillips head screws in the front top( above the oven)area of the range, slide the topof the range forwardand lift it up, remove one screw holding the metal bar under the element, replace the element by usinga a pair of pliers to remove the electrical wires and then reversed the process. I saved a tidy amount doing the job myself.

First I removed 2 screws that held the stove top in place. Raised the stove top and support it. Then, I removed the hold down spring for the burner and removed three wires from the old burner. I found that the connector on the white wire was spread open too much so I crimped it closed for a better fit on the terminal. I reattached the three wires, put the hold down spring back in place, lowered the stove top and installed the 2 screws. JOB DONE

Had to reference original owner's manual for instruction(s) on how to remove oven door. Used several "YouTube" videos to reference oven door design (Oven door glass is actually several layers of glass.) After completing about 30 mins of research and finding the right square drive bit, the repair went smoothly and without complications. The biggest challenge was researching and understanding what part(s) were needed and how to replace them. It seemed liked a lot of work doing the research however it sure beat a $350 repair bill. It cost me $90 and about 1 1/2 hours of total time. Oven works better than ever, thanks parts select for the part(s) and diagram(s) ...

I removed the two screws and then used pliers to pry apart the wiring. I unplugged the connectors and removed the element. The new unit arrived in three days and I plugged it in, replaced the screws and turned the oven on and made a pie! Very Satisfying and easier then I ever thought it would be. We figured we saved $200.00. The service place where we live charges $125.00 to come out and assess and then parts and service on top of that.

Lifted the oven top, removed the controls cover, slipped the lens into the hole and slid the light holder device onto the lens