I changed the temperature sensor and tried again. The stove again went on temp runaway and it was suggested to replace control board which is out of stock. I will have to toss out this stove and buy new as you and no else has this part.
oven temp was not heating up to desired temp and using an oven thermometer to confirm
moved the range out to access back removed 5 screws from back panel removed 1 screw from thermostat installed new one replaced screws, done in 20 minutes problem solved
Oven wires arced and caused the terminal block to melt and become detached from the back of the range
Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely. Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Broiler element would come on during bake cycle intermittently causing overheat with F10 error code
Replaced control board.
Remove power from stove
1. Remove upper sheet metal cover along with plastic trim and sheet metal brace on rear of stove. 2. Disconnect wire connectors to board. The ribbon wire connectors were fragile and difficult, so be careful and pry loose. 3. Remove screws holding board and remove board. 4. Install new board, screws, connectors, trim and sheet metal.
Oven would not heat or sometimes hold heat to set temp
I was able to find the most common reason for my oven's symptom by searching online. I searched for the part I needed but was not confident that I would get the correct part until I looked on partselect.com. After verifying the part number with my owners manual and looking at the video on their website, I decided to order. PartSelect shipped the part as expected, and I was able to install it in less than 30 minutes. The only tool needed for installation was a nut driver. My oven is now working like new.
Many thanks to PartSelect for their comprehensive website and fine service.
Unplugged range; removed back cover; removed old oven probe. Installed new probe; replaced cover; connected power and turned on range - that simple. My only issue was probe was shipped in bubble rap and unit was slightly damaged (bent). Once straightened, the probe could be installed. Probe should have been shipped in sturdy cardboard cylinder or box. I called customer service, they were very nice, and noted my feedback on my account in case the unit fails prematurely.
removed screws from back cover then pulled elect. plug apart. removed screw pulled out probe installed new probe put cover back on very easy only problem was that it said that 88% of time would fix the problem. will this time it didn't work oven still over heating.
Oven would not reach temperature or it would finally reach temp but would not stay warm.
Pulled oven away from cabinet area Unplugged oven from wall outlet Removed screws to free top panel from back of oven Removed screws to free lower panel from back of oven Probe backing was now exposed Unplugged probe from connector Removed one screw from probe housing Twisted probe housing counterclockwise then pulled probe out Reversed the process to install probe Plugged probe into connector Reversed the panel removal process Plugged oven back in to wall outlet Turned on oven and tested with no further issue
Followed the parts select video. However there were differences. Four screws to release stovetop from brackets very difficult to break free even once correct bit identified. No spring clips but studded screw and coil springs let elements fall right off underside bracket. Need fours hands to hold back in place to screw bracket back in place to hold elements.
Called fridgidaire and they told me the a F31 code means my temperature sensor is not working. So I ordered one online. I installed it and I still have F31 code and still won't work. So what now? Do I trust them to tell me another part?