CER3725AAW Magic Chef Range - Instructions

Unplugged the stove removed back cover plate unpluggeg two wires removed racks from oven removed two screws that hold bake element in place and reversed process

Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

Read the ID number from label and ordered part on line. Part was delivered next day. Shut off power to stove and Pulled stove out from cabinet setting. Took out about 12 screws from back pannel and removed it. Pulled out wires (easily seen) from each side of heating unit at back of stove. Went inside oven and took out 1 screw (easily seen) on each side of heating element at back of oven. Heating elemnet came right out. Reversed procedure for installing. Only tool used is a small Phillips screw driver.

I did exactly what your instruction video showed. The most important thing to remember is to TURN THE POWER OFF FIRST.

Unplugged the range, took off back shield (4 screws) unplugged the old part and plugged the new part in, put the shield back on and plugged the range back in. When you remove the light unit behind the lens after unplugging the two contacts slide it sideways toward you, it is slotted, don't try to pull it straight out or you will break the lens.

First, let me say that the (built-in, electric) oven I was working on was made sold by Kenmore, but the error code and, possibly the repair might apply to many other brands. I was getting a beeping sound and an F1 Error Code on the display of the "clock, timer, control board". On-line research said "you're control board needs to be replaced. I spent days looking for a cheap, new one ($400 for a factory replacement did not appeal to me). Then, I tried "re-setting" the control board. In my case, it took- turning off the power to the oven, turning power back on, pressing and holding "clear". After 30 seconds the beeping stopped. 45 seconds later the error code went away and the oven worked. I opened it up and carefully tested everything with a meter while it was on.It has been working flawlessly for two weeks now. So, the repair took me weeks and also less than two minutes, plus time to give it a check-up. Hope this helps. P.S. I had to say that I used a part in order to post this, I did, but not for this repair.

My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.

Remove top oven door,remove two hex head screws located underneath cook top at the front on both sides,slid the range top forward approx. three(3) inches to obtain access needed to unplug the wiring harness, located behind the vertical part of the cook top,removed the cook top,placing it on a padded table with the glass side down,disconnected the three (3)wire spades and unscrewed three screws anchoring heating element to the cook top frame, replaced defective heating assembly with new. Repeated above steps noted above,in reverse order. And yes, all work was done after power was shut off at power panels dedicated oven circuit.

the video that was part of the "part shipped" email was a great help....I had no problem replacing the part...Thanks

The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.

Unscrewed 2 screws from old element, disconnected wires at ends and reconnected to new element. Very easy repair. Actually took longer to get tools than actual repair.

It was easy because the clips were already on the new door gasket. Just had to remove old door gasket and replace it with the new one. Very simple job.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Followed the instruction video that came with the part. Replacing the element is very easy as you just unscrew the two sides, slide the element out, detach the wire on each side, place the new element in and attach the wires, then slide into place and screw the holders in place. Wish everything was this easy to repair.

First, I turned the circuit breaker off to the range. Then, I pulled the range out so that I could get to the screws which held the glass top in place. They were located on the sides of the range. I had to remove the trim pieces on the sides to get to the forward screws. Once that was done, I lifted the glass top, unplugged the wire harness, flpped it over on a protected surface. I noted the numbers on the old coil where the clips held it in place and put the clips on the new coil in the same place. The old wires just clipped on to the new coil exactly as they clipped on to the old coil. I put it all back together and it works great! I am a 70 year old woman who did this all by myself. You young guys should have no problem.