Stove top element not working due to bad receptacle.
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit. My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts. The element is working great now. Whenever I need appliance parts again I'll use partselect.com.
The element broke in two pieces after food dried on it.
First, I unplugged the oven. Then, I removed the two screws that hold the element in place. After that, I gently pulled the element toward the front of the oven until the wires were exposed. I disconnected the wires from the old element, removed the old element and then attached the wires to the new baking element. I gently pushed the new element back into the screw holes and screwed the new element in place. When I plugged the oven back into the wall I heard a pop and thought I'd blown up the oven! Turns out the breaker popped...after fixing the breaker, I turned the oven on and the element worked just fine. I highly recommend PartSelect.com for their fast shipping and great products. I will be ordering from them again for future appliance parts.
one of my burners would only work half the time, and you had to wobble it to make it work
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected the new element using the wire caps, and finished bye rescrewing the element backinto place.
The Burner was getting too hot and you could not regular the tempature
Moved the Appliance out unplugged it and removed the backing plate then Remove the Knob and unscrew the infinite switch then marking the 5 wires to know where the go on the new switch, removing and replaced it with the new one
First, I shut off power to stove(a must). Removed two screws that hold element in place. Gentley pulled element toward door opening. Once wire is expose, hold back of element and pull gentley to seperate element from wire slot. Connect new element to wire and replace screws.
The heating element would not adjust to the knob settings. The element was always at maximum heat, even when I set the knob on minimum heat.
This was easier than putting in a new light switch. The old receptacle would not make the necessary adjustments to the heat element to maintain the desired temperature. Even when I turned the temperature knob to "minimum", the heat element would bun at the maximum temperature. I pulled the element from the Receptacle, raised the stove top to expose the receptacle and wiring. My stove was too heavy to pull from the wall, so I had to go to the breaker box to flip off the breaker. I returned to the stove and snipped the non working receptacle (with a wire cutter) and attached the new receptacle with the ceramic wire nuts, that came with the assembly. I turned the electric-breaker back on, and tested the heat element. The element will now make the on/off adjustments on each temperature setting, to maintain the correct heat. I ordered two receptacles because I wanted a spare. I do a lot of baking during special-day dinners, for my family members... and due to the age of my stove, I bought the bake element as a "back up" if the present Bake-element burns out.
First I opened the door to the oven. Then I opened the box that the part came in. (knife) I then slid the oven rack out of the box and unwrapped the plastic, being careful not to bend or scratch the new rack. Now, this is the tricky part... I had to move the existing rack down one space to make room for the new one. Then carefully slid the new rack in, tipping it slightly and sliding it in. LOL
Element burned through due to something dripping on it & burning.
I looked at the other repair stories on this site & realized it should be simple to do. I first switched off the power at the circuit breaker (range has its own switch). Then used a philips head screw driver to remove the 2 screws that hold the element in place at the back of the oven. Gently pulled the element out. Was able to disconnect the wire on the right side. But the other one would not budge. Thought I would have to get a repair guy out after all. Decided to try again again next day. Put on a pair of leather gloves to get a better grip on the wire (thought pliers might bend the connectors). Was able to wiggle it back & forth & it came loose. Then it was easy to hook up the new one, gently pushing the element connectors into the oven wires & put it back into the oven & replaced the 2 screws holding the element in place. Switched the circuit breaker back on. Turned on the oven and it works like new and no repair person visit!! Thanks for the info at this site.