First, let me start off by saying - this part wouldn't normally break. Because it's a stackable, and my dryer motor went out, the repair company had to move the entire unit from the cubicle. When the repairman tried moving it by using the washer lid ... lets just say he broke the clip. And then we could never get them to come fix the part they broke!
So, I finally ordered the part myself after studying schematics online. I am not a repair person. So, if I could figure this out - anyone can.
Take the middle cover between the washer and dryer off. There are 3 screws holding that panel on. Set the panel and screws aside. There are two "S" shaped clamps at the back. Lift (hard) the front of each one. They will snap free - freeing the whole top of the washing machine. The top has the lid connected. Pull the top towards the front and then rotate it counter-clockwise. It will come right off. This will free up the area the clips go on.
Take the lid completely off to get it out of the way. The clips fit in the holes on the front left and front right. The large square side goes up, and the small side snaps into the hole on the base. Make sure the groove is facing forward for the top cover to slide into. To get the clip to snap into the hole, put the front side down, and push (really hard) on the back side - the side towards the back of the washer. It should snap into place with some pressure.
Now, just put the top cover (with the lid attached) back on, rotate it clockwise, re-clamp it down and replace the middle panel and 3 screws.
Broken belt. Broken idle pully and replace 4 rollers
By watching the video it made the job much easier than I thought it would be. I was very pleased with the speedy delivery of the Dryer kit I had ordered. I had called a local repair facility and they wanted twice as much for the same parts.
my teenage son was messing around and got into the dryer and broke the door catch and bent the door.
removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!
i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.
A piece of cloting snagged and broke the door switch.
Repair job took less than 10 minutes: 1) Unplug Dryer 2) Remove Lint screen and 2 Phillip screws 3) use flat putty knife to depress lid latches while lifting (latches located approx 2 - 3 inches from each side. 4) unplug defective door switch 5) remove 2 Phillip screws that secure the door switch. Reinstall switch repeating the above steps in reverse order and your done.
Half of my pulley was broken off so there were no wrench flats to take it off. I was able to remove it using Channel Locks and the 7/16 wrench shown in the video.
Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.
Dryer made a terrible screeching noise when tumbling.
I followed the repair Vedic and took the drum out and replaced the pulls and bracket. Very straightforward job. Dryer is now as quite as the first day we bought it.
I'm still waiting on my idler pulley. It arrived at Fed EX depot in Tracy CA on December 14th and has still not been shipped. So it is pretty fucking hard for me to install it! Maybe if you had customer service that would answer their phones or reply to my Emails would be helpful
I was reluctant to call a repair service. Typically when an appliance is as old as my dryer (14 years old), service people encourage you to replace, not repair. I had replaced the dryer's motor within the last 5 years and believed my dryer still had life to it. At first, I tried cleaning the lint build up from the dryer cavity and hoses. This worked but only for a couple of days. After reading other successful repair stories on the website, I decided to try replacing the thermal fuse. It was so easy. The part was easily identifiable. It was just a little hard to yank off the connecting wires. Good as new and no service call.
The most difficult part of this repair was making sure I purchased the right part !!! Part Select.com has a great website with pictures of almost every part you could ever need. I was able to select the right part and from there the repair was easy.
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Open breaker and ensure power was off. Checked heating components for continuity.Found thermal fuse had an open circuit.Replaced High limit thermostat and thermal fuse.Now is a good time time check for free flowing vent piping.I discovered mine was crimped below the floor and caused lint build up and obstructing the flow which could have led to the thermal fuse blowing.I replaced the vent piping as well.My wife says the dryer works better now than it ever has.