CE38700BAV Crosley Range - Instructions

unplugged the oven from the 220 volt receptacle. Removed the wire shelves. Unscrewed the two screws holding element to rear of oven. (I didn't know at this point to pull the wires through from the back so I took the back panel of the oven off and unplugged the connectors from the rear). Measured the defective element, ordered, and two days later I reversed the process when the package arrived in the mail. . quite simple. I love it when I can fix something myself. And by fixing, I actually mean "replacing".

Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.

followed you tube instructions. Very helpful feature. thanks

Remove both oven racks. Remove the screw that is on each side of the element holding it in. Pull the element out and disconnect the wire on each side of the element.Remove the bad element and replace it with the new element. Connect the wires to the new element and gently push the element back into place. Put the screws back into place and tighten. Replace the oven racks into oven. Turn oven onand verify that the element is heating. Repair is comlete.

Cut power to range in breaker panel. Then removed two screws (1/4" nutdriver) or phillips head just under top in front. No need to move range out from wall. Once those two screws were out, I lifted the top carefully (since wires are attached to back of range) and propped it up with a piece of spare lumber I had lying around. Then removed two screws holding right rear burner, and doing one wire at a time, pulled the wires from bad burner and reattached wires to new burner. Oh, I did need some pliers to pull the wires from the old burner; they were on real tight. ALSO, the old burner had a series of numbers around it. I quickly learned that these helped you line up the burner correctly. So I noted the numbers with the screw holes in the old burner and made sure I used the same number holes in the new burner. Once new wires were attached, I attached the new burner, aligning the same hole numbers as the removed burner, and everything lined up perfectly. Two screws were inserted to hold the burner. I lowered the top and reinserted the two screws under the front of the top and I was done. Total time was about 13 to 14 minutes. Honestly, very easy. Plus prior to me taking on the project, I had called a Maytag repair shop, who said their fee was $99, plus parts, plus any extra time required for labor, but the latter was not likely something that typically occured.

Remove sensor from oven. Disconnected wire from back. Connected new sensor and reinstalled. Temps now stay stable.

Watched the video and it was as easy as described. Not many things go as easily as this.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

I first pulled out stove, then disconned the power supply. Then removed rear panel which exposed connections to the bake element which was shorted out against one side of the rear panel. Replaced the bake element, then the rear panel followed by pugging in the stove and pushing it back into place then opened the oven door and tested the element to see that it was working properly. Thank you Partselect for your fast service on getting the part that I needed quicky and at a fair price.

I think the installation instructions are fairly self explanatory. This is the second item I've ordered from Parts Select and I'm thrilled with their service. The items are always less expensive than other sites and they deliver what they promise. I would highly recommend them.

i did fine

Turned off Power to oven, flipped breaker. Unscrewed two screws, removed old burner, inserted new burner, screwed in. Turned breaker back on.

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.