CE2500XMW0 Whirlpool Dryer - Instructions

Our make/model was not on the online instruction, but it was similar. Ours had a glass (plastic)front window in the door. To remove the top catch you had to take out the top four screws that hold the door together (philips head screws) allowing you to pull back the gray plastic strip to access the top latch, then replace it like in the online directions using a needle nose pliers. The bottom catch, once the two remaining the screws were out gives you access to the bottom catch. Remove it with the pliers and snap the new ones into place. You can completely take out the window when you replace the bottom latch if you want.

Just pulled the old parts out on door latch and put the new ones in. Thanks Parts Select for your prompt response and easy process for order and shipment.

I followed video instructions. Raised the top, slipped off the front, installed the belt, aligned, installed tension part, reinstalled front, lowered the top and inserted lint trap. Job done. Quick and easy. The video was the key to the whole project.

This was my first dryer repair. The only difficulty I had was figuring out how the belt tensioner was set up with the belt. The old belt broke so I didn't know how it was suppose to work. Anyway, it took a few minute to figure out that one end of the bracket was a "spring" that allowed it to flex a long ways! Pretty easy job.

(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.

The video you had of my dryer was different then my dryer and the pulley was in the middle of the bottom and the motor and fan were in front of it. I had to replace the belt without being able to see what I was doing. I couldn't get it at first then realized there was tension on the pulley wheel and had to pull it towards the other wheel in order to get the belt on there. Once I pulled the wheel it went on really easy. My first time working on a dryer but I knew I could do it myself.

instructions were clear and repair was easy

Well, to Figure the issue I took the entire thing apart. Actually a lot more than needed. I found the torn belt and ordered it. I did not realize I may need a new belt tensioner which is sold with a wheel for the belt to wrap around and be tensioned by. Actually the original just utilized a rubber c or u shaped design(no wheel) for the belt to slide over. Anyways, instead of ordering and waiting for a new wheeled belt tensioner, I installed new belt with all original parts and working fine. I did oil up the drum rollers to reduce noise. And since I took the whole thing apart I cleaned the lint from every place it could hide. Ps a coke can is said to be helpful to hold the drum up while installing the belt but I found a jug of laundry detergent did better. Totally easy project for someone with no appliance repair history

The broken belt was found when I opened the dryer. The part number was on the belt and a quick online search led me to PartSelect. The part was available, delivered in less than 2 days and there was an online video showing the entire repair in detail.

Went to YouTube It was real easy.

Repair went fine. Really easy for the most part. Unfortunately it didn't solve my problem. Great place to get parts though. I'm going to continue my search for the source of the noise

Thank you for the the installation tip I received along with the part. The suggestion of removing the front panel to install the belt made the installation go very smoothly.

I unplugged the dryer then removed 2 Phillips screws from lint trap. Then I popped the top up on each top corner with a screwdriver. I removed the 2 screws holding the front cover. I unclipped the wiring connection and moved the panel. I took out the old belt, put the tensioned back on then put the new belt around the drum and held the drum up with my shoulder then put the belt through the tensioner and put it on the motor spindle by pushing the tensioner back. I put it back together and it worked perfectly. Your video was very helpful. Job was very easy.

Had my wife call the repair man. Since it was Saturday afternoon, no luck. YouTube help me diagnose the problem. I found that the drum belt slipped off the idler pulley assembly and the assembly was laying on the floor. I noticed that the belt was frayed and was probably stretched out which may be why the belt slipped off in the first place. I glued the frayed pieces of the belt back with gorilla glue and clamps. You Tube helped me mount the idler pulley assembly and string the belt correctly. I then ordered the replacement parts through your website. The parts came to my home in a few days and I will fix the dryer properly when I get a chance.

The instruction sheet that comes with the parts is excellent. Follow it and all goes well. Be patient and stay away from the sharp sheet metal edges present in all such appliances !!