Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishes not drying and no heat other than hot tap water
Pulled dishwasher out switch is on very bottom of pump housing, turned dishwasher on its back, took out 1/4" bolt holding on bottom of switch frame, took two very small screwdrivers and small picks to hold open switch clips, while switch was removed checked float for frew movement, put in new switch, removed screw drivers and picks checked to see all locked on new switch in position, replaced bottom plate and bolt, checked burner reset all good now dishwasher heats and drys!
1. Turned off circuit breaker 2. Pulled out dishwasher 3. Disconnected switch and popped out switch 3. Popped in new switch and connected 4. Pushed dishwasher back into place 5. Turned on circuit breaker 6. Turned on dishwasher and it worked
took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together. Works like a champ.
Was able to pop the dishwasher out, lay it on its side and then remove the drain pan. Pump was easily removed after removing the hose bolts and the electrical harness. Swapped the new one in and reversed the steps. A very straightforward repair all said and done.
The replacement went extremely well, the removal and installation of the unit from the cupboard took more time. The pump came off easily, I had to purchase a steel band clamp to replace the crimp clamp that was on the original pump as I did not have a tool for the crimp clamp.
Simply removed old gasket by hand, lined up center of new gasket (white dot was printed on the center of new gasket) with the tub latch and pressed new gasket into place. We have used the dishwasher about a dozen times since and hasn't leaked a drop.
Pulled washer out of space to access cables to the door. Removed moved the cables by stretching springs and unhooking cable from door. Disconnected wire from door to machine in body of machine. Opened door an lifed on an angle that allowed door to be lifted out of hinges. Unscrew and remove hinges on both sides. Remove by simply pulling them straight in direction of the bottom of the door. Then unscrew bolts on either side that are now exposed after taking hinges out. Then push inside of door up and remove. Unscrew the control board unit. Un plug cable to control board. Remove bezel cover. Then carefully unsnap unit case and remove board. Replace with the new board. However since this is a replacement part it must be configured for your machine. Instructions shou you the configuration. However where I ran into a problem was dining out how to set it. There were no switches. What I learned was that altouch it looked like one piece the jumper connections actually were four separate pieces that were tightly fitted together. In order to get the configuration you simply have to lift the jumper connector up. Once done reverse process and your done. If I did not run into that one issue repair time should be 30 minutes tops.
When new gasket arrived almost two weeks after it was sent out from Green Bay, I took out old gasket, marking which side was in and which out. Then, with hands, fit new gasket in place making sure it was centered. No leaking; it worked. Thanks.
My Dishwasher goit damages from broken glass jam pump and clogged drain
Work done" used wet vacuum to remove all water and debris from inside out side dishwasher, used we vacuum to unclog drain, Disconnected drain hose, unplug power cord, water supply line, removed dishwasher, swap all new parts, reconnected everything and done in a zap,
I had to replace a docking port. Parts Select had the part, labeled as stainless, just as this survey indicates. Well folks, the part I received is 100% plastic. It it the correct part, just not stainless. Should it have been stainless due to a faulty plastic design? I don’t know.
I used Parts Select for the simple directions for installation. I was eventually linked to a YouTube video for a completely different docking port. Does my part slip on? Does it press in? I don’t know.
Needless to say, this has been a cheap but frustrating ordeal that is not yet over. Thanks for having the stainless, but really plastic, part and for having directions for some other part available.