C201 Jenn-Air Cooktop - Instructions

Removed old knobs and installed new. No tools were required.

First I disconnect the breaker. I removed the defected receptacle and cut the wires. I connected the new receptacle with parts with the new part. Turned the breaker back on and everthing worked fine.

Fed-Ex delivered the package and within 10 min I had open the package, removed the old knobs and installed the new ones, My wife was very impressed with the ease of the transactionl. It is good to know that we can still get parts for our cook top even though it is 26 years old. Thanks for every thing.

After buying a 'universal' part at Lowe's and it not fitting correctly and shorting out the burner, I went online and found this source for an exact replacement part. Beside having to disassemble the drop in stove burner two or three times it went well when I had the correct part. I lost one screw somewhere and that delayed me a short time to find a replacement. Thus the 1 to 2 hours. It would have been about a 30 minute job if I had been smarter.

I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires were connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.

Two dials available, chose the wrong one, PartSelect paid to have the wrong ones returned and issued credit, while helping to select the correct ones. Friendly, REAL people, who absolutely sealed the deal. I'll always check here first for parts, filters, anything. Thanks PartSelect

Removed 2 screws and i nut. Unplug the old switch and plug in the new switch and presto, back in business. Extremely easy. Part was exactly as pictured. Part arrived within 2 days. Great Co. to buy parts from. Highly recommend Partsselect.

Removed the old ones and snapped on the new.
It was a snap and what a difference! Even though the cooktop is over 20 years old, it looks new again. Thanks to the knowledgeable support people at Part Select.Com we picked the right knobs the first time.

I first replaced the element and the receiver. This required splicing lines which was very easy. It still did not heat (even though my element indicator light was on) so I replaced the switch regulator. This took a little time because of the small space on my model. In fact, I had to replace a wire that had shorted by splicing a 3 inch section into it. When that was done, I simply re-connected the 5 wires in the original positions and reattached the cover. It works like a charm and my wife is delighted because we are hosting a family reunion/baby shower tomorrow!

Unplugged the burner units and replaced the drip pans. Five seconds time per burner.

First I turned off the power to the appliance. Then I took off the face plate where the switch and burner controls are mounted (took off 2 screws). Pulled the assembly out as far as wiring would allow and removed the two wires from the switch followed by removing the two nuts that hold the switch in place.
I reversed the process to install the new switch, turned the power back on and that was that.

I just pulled the electric element out of the slot and dropped the drip pan in place and slipped the electric element back in place and it was ready to go. It looks almost new. We built a new house in 95. It took 17 months to build it. I got the stainless steel cook top that you can have the grill on one side or you can pull the grill off and slip in the burners. It is only 4 burners but it is plenty to work with. It has a down draft.

old filter fell into from removing and cleaning,
removed cover pulled out filter ,replaced it with new one.

Took the front panel off by removing 4 screws. Then remove the switch by loosing the nut hold it. Then replace the wire on the new the way they were on the old switch. Put the panel back on.

Removed old filter, dropped in the new one.
(This really was not a "repair")