C201 Jenn-Air Cooktop - Instructions

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.

removed two screws thenpulled element up unpluged wires

First I removed a screw that held the element in place then disconnected the two wires . Then I just reattached the two wires put the screw back in place and was done in about 10 minutes. Fairly easy fix, I had this go out a few years ago and had a repairman fix it, and saw how easy it was, so this time I did it myself. Easy job!!

Had to drill out screw for old connector bracket and also had to extend wires from controls this took most time. Once done with this used wire cutters to strip back insulation and then put the whole mess back together also used a larger wire nut to reconnect wires.

I first removed power from the stove at the breaker panel. Next, I used the assembly diagrams provided by the parts select website to determine how to open up the stove panel. I opened the oven door to access the four screws holding the front panel holding the knobs. I removed the screws and was able to tilt up the front panel to allow access to the four burner switches. It was easy to swap out the wires on the old defective switch to the new replacement switches. I replaced both defective switches in 15 minutes and tiled the front panel back down into its normal position and put the four screws back into the panel to secure it. Then I turned on the breaker and did a check to see that the parts I replaced were working properly. They were and the total repair time was around 30 minutes without rushing at all.

After I removed the piece of metal separating the two wires, I inserted the unit with no problem.

Our stove is from 1978 and was missing all but one drip bowl. I bought all the replacement parts from all the store, (Walmart, Target, Fred Meyer) nothing fit. I finally found this site and they fit perfectly! Thank you. If I have to keep the stove a while longer at least it looks clean and new now, and it still works great!

Simply removed the old heating element and plug the new element terminals into socket.

We turned off the breaker and removed the screws holding the control panel in place. They are behind in the exhaust area.

The control unit was lifted up to reveal all of the wires and the switches. Using pliers I pulled off the connectors keeping up with which wire was from which connector. The switch then dropped out and the new one went in and wires were reconnected.

It was not difficult. Only challenges were that it was very dense and hard to get at the wires and you had to be careful to keep up with the wire locations.

Well worth the time...I can do something other than boil water on that burner!!

I lifted off the old knobs, pushed on the new. Easy and the cooktop looks brand new!

I removed the old knobs and replaced with the new ones. We also replaced one of the switches which the knobs fit on, because I broke the switch off with a Cast iron skillet.

The burned control switch was not functioning. It took a while to find the range model number and then the part number of the switch. It was cool that I could see a picture of the part with the part number on the internet so that I was sure to buy the right part.
Once the part arrived, I turned off the power to the range (circuit breaker, 220 V) removed two screws, used nut driver to disconnect switch handle, marked the 5 wires going to the switch, used the needle nose plier to remove the wires, the attached wired to the new switch, placed switch back into position, used nut driver to attach switch to the control unit. Rescrewed control unit in place with two screws.
turned on circuit breaker and tested. All good.
It is clear that this old Jenn Air range and be completely redone to good as new. All parts are available

Turned off power at breaker. Removed screws holding control knobs in position. Removed knob and unscrewed nut holding switch in place. Noted wire positions and undid connections. Connected wires to new unit. Replaced nut and screws and control knob. Restored power and checked operation. You can do this. Don't call an electrician.

I TURNED OFF THE POWER TO THE GRILL FIRST. Then Removed the knob on the top face plate and then removed the 2 self tapping screws at the high end and this allowed the face plate to be pushed forward. And allowed access to remove the switch I removed the wires one at a time and replaced them on the new switch. All done in 20 minutes.

removed all for knobs and replced with new ones