Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The washer machine didn’t start the cycle. Had a weird sound. Then f 30 was ther error code. With research internet it was easy to know about the motor dispenser problem
I did follow step by step your YouTube video. I’m a woman. There was nothing heavy in the process. You have to be careful that’s it. Thank you for the instructions. I fixed it with the YouTube tutorial you provided. Really nice from you people.
Took door off with a Phillips screwdriver went to hardware store with door so he could match up the 6pt screwdrivers that were needed. No more then 1 hour to do.
I took the machine top off, then removed the control panel, removed old wire ring clamps. Removed door, removed inner clamp, water inlet tube, and bellows. Lubed up the new bellows with food grade silicone. Replaced the water inlet, inner clamp, door, outer spring clamp, reassembled the washer body and control panel and then ate a pizza.
replaced actuator switch. It did not fix the problem. Replaced actuator arm, and fixed. Needed the switch because gears were stripped. Needed the arm because it seems over time, the arm straightened, thereby increasing its length so that the rotation of the switch bound up during its cycle.
Washer was filling up with water when not on or running.
Removed old valve and replaced it following the directions provided. Then flushed out intake hoses and cleaned aerators. Easy repair. Your directions were very helpful and user friendly!
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.
Broken Strike on Washer Door - prevented door from latching, and washer would not start
The end of the strike had broken off, and the pictures did not clearly show there was a cross-member at the end of the strike. That crossmember is what broke on the old strike. The strike has only two screws, both requiring a Torx bit (#20, I believe). Unscrew both screws to remove the strike plate. It was a little difficult to get out - it has a curved top to lock into the top slot, but the bottom slides slightly down into another slot. There isn't a lot of room in the opening to slide the strike up and down and get it out. Putting the new strike on is easier - ensure the curved end fits into the slot at the top and slide it up just a bit, push the bottom of the strike plate in, then let it drop right into place, and reinsert the screws. The only problem I had was the strike's holes for the screws are slotted horizontally, so the strike can be positioned across almost 3/8". The latch would not engage the strike the first time, so I had to loosen the screws and reposition the strike a bit. This time it latched, but the fit wasn't quite right, so I adjusted it again to get it where I needed it.
Removed rear cover (6 screws) unpluged harness from motor control and removed same. Replaced motor control reinstalled harness. Replaced rear cover. Parts used motor control board.
Shut off water and disconnect hot and cold hoses. Use nut driver to remove three screws at back/top of washer. Slide top of washer back and up to remove. Use pliers to loosen band clamp on rubber hose and pull away from valve assembly. With fingers, disconnect wiring from hot and cold solenoids. Use allen wrench to remove valve assembly from frame of washer. Use reverse order to install replacement valve, although you can leave the top off the washer until you've checked for leaks.