BEP410WB0 Roper Range - Instructions

First I turned off the circuit breaker...just to be safe. I removed the two screws that hold the element in place. I was surprised you didn't went new screws, but that was OK. I pulled out the old one, and pulled out the two wires. It was tricky, for me, to pull apart the old wires. Luckily, a friend was braver than I, and just pulled them apart using a little muscle, and easily connected the new wires. I screwed it back in, and it was done! I was really impressed with how quickly it arrived at my door, too.

it was really easy. The most time consuming is removing an replacing the unit from the built-in cabinet.

SUPER EASY! The part arrived very quickly. I turned off the circuit breaker, unscrewed the few nuts, pulled out the element and reversed the process. 'works beautifully! Thanks so much.

1. remove 2 screws holding element in place
2. unscrew the wires from the old element
3. the connectors on the new element was different from the old one
4. cut old connectors from wires
5. prepare wires for new connectors
6. install new connectors
7. connect the new element to the wires
8. replace the 2 screws removed in step 1
9. test the repair
10 it worked great.

First, I removed the 2 screws holding the element in place. Next, I pulled the element out abotu 4 inches and disconnected the wires attached to the element. I was able to do one by hand, but the other required needle nosed pliers. (be careful not to pinch the connecting wire). Then I attached the wires to the new element. Lastly, I replaced the 2 screws to hold the new element in place.

The broiler unit had disintegrated at both connections. I removed the two screws in the top of the oven holder the unit, pulled out the unit, measured and ordered a replacement.

To replace the element, I pulled out the stove, removed the rear panel, located the connections for the broiler unit, remove parts of the old unit. I then attached the new unit to the top of the oven with the two screws, went around back and pushed in the two connections, replaced the back cover and replace the stove. It took about 30 minutes because I cleaned everything and sprayed bug spay (another plus for doing the repair myself).

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Inspect new part; collect tools; TURN OFF BREAKER; remove two screws holding defective element (KEEP!); install new element using saved screws; turn power back on; test; celebrate!

After unpacking and checking the unit that was mailed to me, I cleaned the ends of both the connections in the oven and the connections on the part, then plugged them together and screwed the plates in place in the oven. The oven worked immediately and still is working very efficiently. I had no problems at all with the installation.

Took two screws out of burned out unit. Pulled element forward and pulled off connectors. Replaced new element on connectors and screwed back in. Extremely simple. Less than 10 minutes.

Turned off power at circuit breaker. Removed 4 phillips screws from area over oven door. Pulled control panel out and twisted to clear top rail. Pulled two wires off of old switch.Pulled old switch through panel. Inserted new switch. Attached the two wires to new switch. Replaced panel and inserted four screws. Turned on power - it works!

removed old burner. 2 screws. disconnected connectors and reconnected new burner screwed back in place. turned on stove worked first time. perfect fit. 15 minutes total repair time. item arrived promptly and at half the price of the Whirlpool website.

I killed the circuit breaker to the oven, then double checked with an electrical tester. I removed the oven door for easy access, unscrewed the element bracket screws, plugged in the new element and then I reversed the steps above.

I am very happy with PartSelect and will use them in the future for all my appliance parts needs.

My son is very handy. He had no trouble installing the new heating unit. The new part seems to be working well.

removed old burned out element, installed new element