Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Gas flame turns off after a while, dryer keeps turning but no heat is generated.
Before this fix which worked beautifully, I tried replacing the flame sensor which did not work. To read that story, search under part number PS459818 (Flame Sensor). Our model is a Westinghouse, so access to the unit is a bit different than the other stories. It's a stacked front-loader sitting on top of a washing machine.
1. Open the little front door (lower left side) by unscrewing the little screw right below it. The door will pivot and slide out vertically. 2. Disconnect the electrical main lead coming from the back of the unit (just in case). 3. Close the gas switch lever on main gas pipe coming from the back on left side (just in case). 2. Remove 2 phillips screws on top of the metal bracket holding the two coils. The screws have to be removed completely along with the bracket. It's easy, they are right in front and there is room for the screwdriver. Use a thin long one instead of one with multiple bits to better align with the screws, which are very close to the coils. 3. The two coils slide right out and are very different so it's easy to keep them straight. Remove electrical connectors before or after removing the coils (I marked the plastic on top with a sharpie to keep them in the right orientation). 4. Drop in the two new coils and reconnect them to the electrical leads. 5. Reconnect main electrical lead from back (match wire colors) 6. Reopen gas lever on gas pipe. 7. Drop in front cover at an angle, tilt vertically and put screw back underneath. Use magnetized screwdriver or a piece of scotch tape to hold the screw or it might fall off the screwdriver. 8. Voila'. It worked.
This website is great. Our dryer is a Westinghouse bought in 1991 (almost 20 years old!) and with this fix it's just like new. In 1994 we used parts bought here to fix our washing machine (Westinghouse LT350RXW1). That machine is now 15 years old and still going!
I definitely would not have tried to do this had it not been for the other testimonials written here. But it sounded so easy, I had to just try it (the repair man estimated that with parts and labor, we would be looking at somewhere between $250 and $300!).
The repair itself took less than 15 min, but I spend a good deal of time looking around the garage for a few screwdrivers and my socket set (me and tools don't meet too often). I could simply pry up the top cover on the dryer with my hands, then got it all the way up after removing two screws from the lint trap and undoing this really annoying wire connector thing. From there the front panel lifted off. To remove the drum, just had to release the tensonier on the belt, and it came right out. From this point it was really obvious where the replacement parts would be going. A few screws later, and I could swap the parts, and put humpty dumpty back together again.
As others have described in more detail... I lifted the top, removed the 2 screws holding the front panel (one on each side, inside the control panel on either side - not the easiest to get at, but not too bad), popped the clips holding the front panel in place and removed it. With the front panel off, the location of the coils is obvious (lower left side). The only challenging aspect of this repair is that the 2 screws holding the coils in place are really torqued in so it was crucial to use the exactly correct size screwdriver and not let the screwdriver slip while unscrewing those screws. Actually swapping out the coils took seconds, of course they have to go in exactly the same way as the old ones. I did take a few minutes extra to vacuum out years of lint from the inside of the dryer. Overall, much easier and cheaper than I was expecting and now I know where everything is inside the cabinet.
The igniter glowed red and the gas did not come on !
Read your article on possible repairs for different symptoms and after dis assembling and cleaning certain parts took a chance on the flame sensor, which turned out to be the culprit. Your help was a valuable tool in the repair process ! What would be the bee's knee's would be the resistance reading on the sensors that monitor the system for a more accurate diagnostic approach. But none the less you definitely aided in the repair of my propane gas dryer. Thank you very much ! And by the way the 3-4 day wait for the part was well worth the half price I paid versus our small town repair facility, Thanx again
Dryer did not completely dry the clothes. It required several cycles to dry clothes.
I unplugged the dryer and pryed open the top by inserting a screw driver in the space 1inch from the top on the side. After i opened it and lifed it up, I removed the one screw on both sides found in the inner part towards the front top. I then removed the front panel. The coils are toward the bottom left side. They are held in by a bracket which is held in by 2 screws. I removed the outer screw and loosened the inner screw. ( you can remove both screws but it was not necessary).I then swumg the bracket around and was able to lift out the coils. I removed the connectors and relaced the coils. Once done I re-assembled the dryer. The problem was solved.
Dryer was working, only burner was working occasionally only. So, in result the drying time was very long, and clothes were cold and still not satisfactionally dry; occasionally only it was hot. It became obvious to me that gas burner only occasionally is working. On the Internet I found some instructables, mostly on YouTube, but also on this site (the Burner diagram): thus I have learned that the culprit must be the two tiny ignition coils: they worked only sometimes, so it was only a jeopardy when checking them using a continuation meter (voltmeter with continuation feature). For the access to the burner combo I used a small checking door right below the large door, in front wall of the dryer. There are only two small screws which hold a small piece of metal which cover these tiny coils. However, I had to disconnect the burner from gas pipe to get better access to those screws. (Of course, I also disconnected the dryer from power and I had to disconnect those wire connections on the burner combo to get access to the burner). It works perfectly after this repair.
Gas dryer would generate heat at the beginning of the cycle but would stop after 5 min and would start making a buzzing noise.
Unplug from electric outlet. Use putty knife to press on two brackets holding the top cover. Raise top cover. Unscrew two screws holding the front panel. Raise front panel up and move to the right (careful with the wires). Disconnect wires from coils. Unscrew two screws holding a small bracket holding the coils. Replace coils and reassemble everything. (HINT: make sure you drum is empty. Mine contained dump clothes, and it turned out front panel actually provides support to the drum, so mine was hanging there with some weight in it - probably not good).
The clothes were not getting dry, no matter how long they ran
The first thing I did was logged onto the internet to search the web for my dryer information. Next, after I found the correct model, the site referred me to the parts section and that is where I determined the problem was the M series ignition coil. I then unplugged the dryer and turned off the gas. I took a screwdriver and popped the top off and cut the wire straps that held the door strips and the light to the front panel. I then unplugged the door switch at the connector - HOWEVER - DO NOT TRY TO REMOVE THE WIRES FROM THE ACTUAL DOOR SWITCH BECAUSE THEY ARE VERY FRAGILE AND CAN EASILY BREAK. Next, I removed the two screws that hold the front panel on. By using a slight bit of pressure, I removed the front panel and was able to locate where the ignition coil switch was. (It was right in front) I then removed the two screws that held the clamp down, as well as the bad coils. The coils easily slid off the post and the new pieces slid back on just as easy. I then replaced the screws and clamps to hold the new pieces in place and replaced the front panel. **NOTE ~ while the front panel is off, it would be a good time to clean out all the built up dirt and lint that has accumulated over the years. Lastly, I re-connected all switches and wires and replaced the top panel. Once I turned the gas back on, everything ran beautifully.
I lifted the top at the front edge, slid the top back, disconnected the ground wire connected to the top at the rear edge, just slides off. Then removed the phillips screws on the inside front edge, only one on each side,near top of dryer disconnect the wiring harness at the right side, cut the nylon tie strap holding harness also. Tip front panel out a little and lift up, comes right off. The coils are in plain site on the gas valve, remove the wires, and the two screws holding the bracket that holdes them in place, slide the old ones off and start putting back together. I also used a vacume and cleaned all the lint and dust off everything I could, including the air intake at the rear of machine, "Peice of Cake"
You must disconnect appliance from the gas, water and vent to access the back. Remove the top of the dryer which then allows you to remove the rear panel by removing all screws, You may also have to remove 2 electrical connections to get this panel off. Now you have access to the air duct. To remove the air duct there are 3 screws inside the dryer and 2 screws on the lower part of the air duct. One of the lower screws is facing toward the inside of the dryer and you will need a 12"+ screwdriver to be able to remove. Once you do all that install the new part and repeat steps in reverse.
I removed the front, top and back panels of the dryer, installed belt around drum and through the pulley system so the belt was snug, replaced all screws and panels, and done.
I recently ordered parts for a gas dryer, Frigidaire GLGQ2152 ES3. When I received an igniter part number PS12585650 order number 14700077, the igniter was broken when I opened the box. I believe what happened is that the new metal bracket was wrapped in the bubble wrap along with the igniter. I called customer service and was setup to return the igniter which I did. Also, I ordered a second igniter. I receive the second one and it wasn't broken and the bracket was outside the bubble wrap during shipment.
As far as the installation of the "replacement" igniter into the gas dryer, I could not find instructions on how to install it. The received igniter is much different than the original. There was a small instruction sheet stating that the new igniter is different but can be installed using the new bracket that came with the igniter. But again there were no instructions on how to do this. It took me great effort to figure out how to do this.
The old igniter had to be removed by removing the old bracket assembly that the igniter was mounted on. The new igniter had to be installed onto the new bracket and then by sliding the new assembly under the old assembly, the screws were reinstalled. Although the holes where the original screws were to be screwed into were too small, they had to be drilled out. There was no hardware (screws) to install the "replacement" igniter onto the shipped bracket.
After much work, I finally got the new igniter installed (without breaking it) with the new bracket and the dryer is back in operation.
Dryer was very noisy, like a vibration,or bad bearing
First i replaced the drum bushing on the rear of the drum ,it was definitely bad but noise was still there Decided it was the blower assy , pulled the dryer out disconnected the power,took off the frt panel with the door, disconnected the wiring to motor remover motor and fan assy, most trouble i had was fan is on motor with reverse threads messed with removing fan until I figured out it was backwards after that removed old fan and housing installed new one ,put dryer back together,started it and only normal noises Good for another 5 years Chuck
