BA7500 Maytag Washer - Instructions

Removed the front of the washing machine. Located & removed the water inlet valve from it's mounting on the back
inside face of machine. Replaced water valve, & restarted machine. Like new again!

Can't say enough about the speed of parts delivery & professionalism and accuracy recieved from the team at Parts Select. Thanx again,

Greg W.

took hose off then took three 5/16 screws then clamp off reversed order to put back on check for leaks ok

1. Identify washer model and symptom
2. review page of suggested part; view installation video
3. order part with standard shipping
4. receive part next day and install just as the video showed

Entire job from going to PartSelect website to completion took less than 24 hours. Hardest part was moving the washing machine. Machine is nineteen years old and now works perfectly. Unmatched service.

Removed door panel to get to the electric control conponents and noticed a burned wire to one of the door microswitches. Ordered the door switch repair kit from PartSelect. Also, ordered and replaced the thermal fuse at the same time since it was only $12 and didn't know if that blew at the same time the switch cooked. I had the parts coming standard delivery (3-5 days), but they arrived the very next day. Parts included easy to follow directions.Job went pretty smooth and the dishwasher works again Good experience!

Shut off water supply, unplugged washer power, removed supply hoses from old washer valve assembly, removed valve mounting plate and removed old valve assembly from mounting plate, diagrammed and disconnected hot and cold solenoid valve wiring and removed valve assembly outlet hose. Installed and connected new valve, performing the preceding steps in reverse order. pressurized new valve, verified valve function and checked for leaks and placed washer back in service.

Removed front panel, removed bolts from the front of top panel, lifted. Removed hoses, then 4 screws from siphon break at top right rear of machine, removed siphon break. Installed replacement siphon break and secured with screws. Put some dish soap in hoses and slid them into place and tightened clamps. (It is necessary to move the top panel up and down at various times in the process to do all of this.) Then secured the top with the front bolts. Then installed front panel. Tested the machine, no leak.

Loosened the hose coupling, removed the old washer and strainer; cleaned the opening; flushed the opening; installed new strainer and washer; reattached hose and "Bob's your uncle"! No problem.

pulled the washer drain hose off and replace it with a new one. it was so stiff it would not flex properly. Probably 30 years old. I broke the Syphon Break elbow because of the stiff drain hose. unscrewed 4 sheet metal screws where the Syphon Break Elbow goes through back of washing machine. opened the access hole for my arm below - 1 screw. reached up and pulled broken part out from the inside approx 12- 16 inches above. Slid the new part into place. remounted the 4 screws hold connection together. recovered access hole and attached new Drain hose with a band clamp. The new hose had 3 different size ends that can be cut to fit. I had to cut down to the smallest diameter hose. (1 inch, 1.25, or 1.5 inch). Ten to 15 minutes tops

Took off front washer panel push drum to one side reached in took out four screws on back of washer removed siphon break from ebow for drain hose pulled siphon break to front of washer cut hose clamp installed new part reversed procedure to put washer together Tested operation worked fine no leaks no water on floor wife very pleased with fix Thanks again for fast delivery and great inventory of parts

Unplug washing machine.
Disconnect water supply hoses.
Remove valve service panel, 1 screw.
Remove valve from panel with wires attached. 2 screws.
Remove water outlet hose from old valve.
Mount new valve to panel. 2 screws.
Attach water outlet to valve.
Move wires from old valve to new valve.
Dress wires.
Reinstall valve service panel, 1 screw.
Install new wire braded supply hoses.
Done. Hope to get another 20 years of service.

Washer is enclosed in a walled partition. I spent more time moving the washer out so I could get to the back of the machine. Due to Maytag's design of a removal sheet metal panel holding the valve the entire water valve replacement was performed outside of the machine. The replacement valve was an exact duplicate and made it a simple swap out. More time was spent removing inlet hoses and outlet hose then in actual valve replacement.

First turned off water and unplugged washer. Removed hoses and then removed bracket. The new part needed the bracket from the old mixer which was no problem - 3 screws. Removed electrical plugs from old mixer-placed on new one.No problems - worked like new. Thanks for your prompt shipment and the good illustrations of the parts when I was searching.. Also, half the price of local parts houses and it would still have to be ordered.

Took out 2 5/16" screws and loosened top and took off two ground wires and 2 hot wires for cold & hot water solenoids and removed & replaced solenoid wires and fill hose. Also Had fantastic delivery of parts.

Removed the four screws that hold the part and also loosened the screw for a cover. Moved cover to gain access to inside of machine. Removed broken piece and replaced. Tightened screws and replaced plate. No leaks.

Diagnosed the problem and ordered the part online in about 15 minutes. Part arrived about 3 days later. I followed the directions that came with the part and VOILA! washing amchine fixed. I unplugged the washing machine. I unscrewed the the screws at the back of the machine. Pulled out the faulty part and disconnected the electrical wires. Connected the electrical wires to the new part, and screwed it back in. In less than 30 minutes, I was done.