AZ2727GIHW Maytag Refrigerator - Instructions

Removed the door assembly with 4 Torx screws, replaced the broken door with the new one. The assembly is spring closed, so had to be pivoted into place. Then the door didn't open when the ice button was pushed, but made a loud snapping noise. After removal again, it was determined that the solenoid was not attached properly to the arm. After this was done and the whole assembly was put back on the door, everything worked fine.

Watch out for the circuit board at the front of the assembly, it carries a pretty good bite!

First I compared the old parts and new parts to see if I had ordered the right thing then I inserted the new stop into the door. Since the stop has a lip that needs to fit into the slot I the door, I used a hammer to push the part up so it would lock into the hole. Very Simple

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.

Very easy to order from parts select. Took seconds to replace.

No tool required! Pulled out tray, emptied ice into large bowl for reuse. Pushed in and pulled from inside the coil springed auger until could get old plastic ring off and put new one on. Useing care not to apply too much pressure to ice dispensing end so as not to break housing. Have to turn auger assembly at an angle to compress enough and get old ring off. Needs a little physical strenth & care not to force plastic housing to breaking point. Worked great reused saved ice. Took less than 10 minutes

Remove ice maker. Remove single screw from under enclosure. Unplug wiring harness from refrigerator. Remove Ice enclosure. Removed metal yoke (left hand thread) with light tap from rubber hammer then removed all screws holding motor assembly and yoke assembly. Reverse the procedure to install components. Plug in wiring harness and install enclosure. Align ice dispenser with metal yoke on enclosure and install ice dispenser.

Empty freezer

Shut off power

Use two striaght screw drivers to hold the electrical connector clamps open

Remove connector, noting which wire colors were from top to bottom

Remove clamp screw under the enclosure

Remove the Yoke from the motor. It is attached by a left handed thread. Tapping with a small hammer may be necessary to free the locked position. Keep the washer safe.

Remove screws from ther motor, the solenoid, and the plastic solenoid armature cover.

Fit the motor and solenoid to the new enclosure, using existing screws.

Fit the Yoke on to the motor shaft.

Attach the solenoid to the enclosure.

Slide the armature into the solenoid, and screw the armature guide and cover into place.

Test movem,ent of the solenoid armature by hand, to ensure free movement.

Attach a string loop to the end of the connector so that it stays at the top while the enclosure is put into place.
Slide the enclosure in, reconnect, add retaining screw.

Disconnected power to frig.
Had to wait for "ice block to defrost in ice bin and enclosure before removal. Caused by water from a frozen water tube overflowing into bin. This in turn "locked" the screw in place causing the motor to break from its mount on enclosure when trying to get ice.
Removed broken enclosure,one screw on left side and lift out leaving motor hanging. Disconnected wiring marking where they would reattach removed other part from enclosure. Unsnapped wiring harness from back wall.
Removed yoke from motor. Easier than I thought . A light tap with a hammer (right side with yoke facing you) it spun right off.
Attached wiring to parts and then installed parts to enclosure. Tapped yoke with hammer again. Repositioned encloser and from under reached up and plugged in the harness into the back wall.
Mounted encluser and ice maker.
Ice maker is up and running.
Will pay more attention when screw is bound up and not from blocked dispenser.
Thanks for Part and How to section..

Replace the refrigerator lightbulb while traveling 88 mph then turned on the flux capacitor being carful not to get stuck in a worm hole. This allows you to fix the problem before it starts to go bad.

Replaced filter with by-pass plug. For some reason though, ice maker does no longer functions, although there is flow out of the cold water tap. Is the design of the bypass plug such that, when installed, it impedes flow to the ice-maker?

Thanks

Took a putty knife and
Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place

I watched your online video on how to take out the old filter, and then to replace it with the new filter. It was as easy as on the video. Thanks!

First I removed the 1 screw holding the Ice Enclosure in place. The enclosure would then pull out. However the wire in back was plugged in and you could not see how the female plug was locked to the male plug. By squeezing the top and bottom edges of the plug you will release the lock and plug will release with a pull.
Then I removed the unit from fridge.
after removing the 8 screws holding the motor and other fixture, I tried to install in replacement enclosure.
unfortunately, the u-drive that is attached to the gear box shaft and is used to turn the Ice despincer worm, was on so tight I could not remove it. (tried everything)
I then took a Dremal tool with disc cutter and where the shaft hole is I cut a rectangular hole large enough for the u-drive to fit through. Be careful not to cut the plastic braces behind the panel.
The motor and gear box then fits in the slots and you can screw in place.
Note: the green ground wire and red wire are tape together. the ground wire to gorund a red wire to closest terminal. White wire to terminal on bottom.
Slid unit part way back in freezer, reach in back and connect plug. (only connects one way)
Then slide rest of the way in, insert screw to hold in place. Good Luck, mine works great.