AW25K3A Admiral Washer - Instructions

Watch video, fallowed it's instructions which made it a "piece of cake"

I removed the belt and pully form under the washer. Lefted the top cover, removed the hardware above the tub, took the front cover panel off to gain access to the tub. Used pliers to remove the springs. Lifted the tub up high enough to install the snubber ring. After putting tht washer back together and doing the first the load the washer stopped banging.

Remove the access panel on the lower back of the washer, the pump is on the rear left side and is help in place by 3 screws. Remove both hoses with pliers and the screws and the pump is out. Install the new pump and connect the hoses and lean the washer back to connect the belt on the bottom.

Examined the washer and determined the hoses were fine. Removed the access panel from the back of the washer, pulled out the drain pump. Looking inside the pump while turning the pulley I was able to determine nothing inside the pump was moving. Once the pump was pulled apart (4 screws) it was obvious the wheel inside the pump broke off. We ordered the new part on sunday (from partselect) and it was sitting on my door step wednesday. That's fast. 30 Minutes later everything was hooked back up and we were back in business. One last point: when putting the drive belt back on, put the belt on the 2 small pulleys first, then put it on the large pulley last. Thanks to partselct !

Just followed the video! 1. Removed the belt. 2. Removed the back (the video said the water pump was in the front, but mine was in the back), 3. Removed the hoses (using bucket and towels to collect the water, 4. Removed the three screws that hold the pump in place, 5. Put in the new pump, 6. Connected the hoses, 7. Reinstalled the belt, and 8. Fretted as the first load of clothes were washed...

I had some expert advise on what the problem was so that made it easier to consentrate on the fix. I was surprised to find so much information on this web page. Getting the right part ordered was also very easy. The repair instructions given by other people was all correct, tiling the machine to get the belt off, removing the back access panel, was all correct and made it easy. The hard part was getting the machine out of the small wash room and into the garage where I had room to work on it. A good dolly and a wooden ramp came in handy . A word of advice woud be to operate the hot & cold water faucets on & off every year or so to be sure they work easily when the time comes, maybe an emergency. After 12 years I was worried my valves would give me a problem. (.they didnt).

Followed video instructions. Most difficult part was re-installing the E-clip on the bearing.

turn off water to washer, disconnected hoses. Tilted over to open rear access panel removed old worn part replaced with new part reattached pulley. Replace access panel flipped back in operation position. Connected hose turned on water. Put small load in and turned on washer worked great.

I used Utube to search for Performa Washing machine jumping around. You will find several videos that will be extreamly helpful in understanding exactly how to go about changing the sunbber ring. The snubber ring is fairly easy to change out. Quarters were used to hold the springs apart so they can be removed. Push the tub forward and away from the spring you want to remove. Install several quarters in the spring. Use as many as you can get in. Then pull the tub toward you and the spring can be removed from the tub. There are six springs to remove. I just left them laying in place at the bottom of the washing machine base. There are videos on utube also of using the quarters to remove the springs. Of course if you have spring removal tool for this purpose so much the better. I didn't have one. Good luck with your install. MB in TN

I heard buziing and smelled a burning smell with my washer so i got on your website and watched a video how to take the washer apart and what the problems could be and determined it was the drainpump so i took the 3 bolts holding it on out and inspected the belt while i had it off , and ordered the part from you guys and put it on your information was very helpful