ATF1910DRW Admiral Refrigerator - Instructions

First I unplugged wiring harness from the inside of the freezer. Then removed two small bolts on top side and one on the bottom. Then took it out of the freezer. Then unplugged the wiring harness from the ice maker. Then plugged it into the new ice maker. Then reinstalled it back into the freezer with the three bolts.Then plugged it back in.

After reading one of the repair stories that applied to my same problem I knew exactly what to do from there. It was simple to remove the old one and install the new one. My ice maker is working great and no more overflowing water.

I found your website with the step by step video on how to replace the ice maker on my refrigerator. It looked really simple, so I ordered the part from you and it was here in 2 days. It absolutely took less than 15 min to remove the old ice maker and replace it with the new one----and it works. You helped me save close to $200.00. Thank you!!!

Had to remove the ice-maker (also easier than trying to work inside the freezer letting all the cold air out). A few mounting screws and an electrical connection in the back. After it was out you will need to remove the cover (not the superficial cover that just pries off) where the gear is behind it, just far enough so you can get the mounting tabs on the ice-stripper in. In order to to move this cover out, after removing the screws (the obvious), you'll need needle nose pliers to ever so slightly squeeze the plastic clips together that hold the plastic movable bracket and the metal ice level arm/switch, so it will pop out. Once you have room to put the ice stripper in, it should just all snap back together, then proceed in reverse to put it all back together.

Replaced ice maker assembly, 5 screws out, unplug the wire, take some attachments off the old ice maker and put it on the new one, plug it in, 5 screws in...done. I did have to take a mirror to see how to unclip the wire, which turned out to be the hardest part of the whole job..

It was easy and my daughter did most of the work while I assisted.
Removed contents from freezer, unplugged refrigerator, shut off water to ice maker. Used hairdryer to thaw inside, placed ice catcher in sink to thaw. Removed defective ice maker and transferred trip lever and wire bundle to new unit. Installed new unit, bent mounting bracket located on bottom of new unit so that when installed the ice maker is horozontally level. Plugged refrig in and turned on water. Water does not come in right away as the temp probably has to be restored to freezing level before things start to work....so just let it run. In the morning lots of nice cubes and no leaks...hooray!

yup

Removed mounting screws
Disconnected file hose
Flipped unit over to remove connecter
(This was the only difficult operation; unpluging & pluging it in)
New part fit was very good
Reversed the disassembly order to install
New assembly had to cycle a while to produce ice cubes. I'm very happy now, so bring on the hot weather.

Pulled the plug on the refrig. ( This is important since the heating bar on the bottom of the ice maker could come on as soon as you plug it in and burn your hand ). Removed the ice bin to get it out of the way and then removed the 1/4" hex screw from the support bracket under the old ice maker ( don't lose it ). Pushed up on the old ice maker to dislodge it from the 2 support clips on the top of the ice maker. Squeezed both sides of the wire harness plug and pulled it out and removed the old ice maker. Removed the wire harness and level bar from the old ice maker and installed them on the new ice maker. Plugged the ice maker wire harness into the female receptacle in the freezer. Popped the ice maker in to the top support clips making sure the rubber water chute from the refrig. was in place in the round ice maker receptacle. Plugged bak in the refrig. and I was getting ice in about 2 hours. Working fine after 1 week producing plenty of ice. RussK---

Well I could what laid on the floor and replaced it but I didn't I emptied refrigerator laid it over change the motor then stood it back up actual work about three hours

following the advice of this site, purchased a new ice maker. Old one was simple to unhook and remove and new one was just as easy to install. Within no time at all, I had ice being made and it has been working perfect since. Thank you for the help...

I followed your posted video. Did step by step as video instructed and in about 30 minutes finished. Ice was made approx 30 minutes later. I hope you do more videos, a picture is worth a thousand words.

It wasn't quite as easy to get to the bolts as the video showed. The lay out of the part wasn't exactly like the video either. However, I managed to put the new part in. Unfortunately, it didn't solve the problem. At first the fridge cycled on and off but after 12 hrs it started to freeze liquids again. Since the appliance was 17 years old we opted to just get a new one.

Pulled socket out of housing, unplugged it from source, plugged in new socket and replaced the socket into housing, screwed in bulb and it worked!!

Removed Ice bin, remove rails on left side that hold ice bin. Remove one screw holding ice maker to refrigerator wall,then lift ice maker off holding screws. Unplug wire harness from back of refrigerator. Remove wire harness and loading wire from old ice maker and install on new unit. Re-install new ice maker by reversing steps. Videos where very helpful.