AT19M8V (DE55A) Admiral Refrigerator - Instructions

Instead of the ice maker unclipping from the wall after one 1/4" screw being removed from the bracket, I had to remove three of the 4 Phillips head screws from the ice bucket slider below the ice maker and swivel it down to allow the ice maker bracket to clear. The two 1/4" screws holding the ice maker to the wall at the top had to be removed and then the ice maker could be pulled away from the freezer wall. The rest of the instructions went according to the video and went well.

removed the cover from the back of the refrigerator, and used the nutdriver to loosen screw on the single outlet water valve, removed the old water valve and the hoses to it. Connected the hoses to the new valve and attached to the wall of the refrigerator by tightening the screw. Then removed the old ice maker from the inside of the refrigerator, by loosening the two screws and attached the new one, I tightened the screws and then I was done. It is working great.

Remove 1 screw under ice maker. Gently pull downwards to unhook ice maker. Disconnected 4 pin wire connector. Remove and set aside the cover and wire loop you will need on new ice maker. Reverse the steps to install new maker. Once new ice maker is installed you will have to wait 2-4 hours for ice. There is a thermostat that will need to reach 10 degrees F to operate.

Add the new one it was slightly different than the original but it worked out perfect.

Just kept working on it.

Merely remove the front bottom screw that attached the ice maker to the refrigerator
Lift the ice maker gently off of the 2 top screws
Unplug the icemaker wiring harness from the back of the refrigerator, and remove
Snap off the end of the maker and remove the keeper for the wire arm
Remove the wire arm and install on new maker
Unplug the wiring harness from the old maker and plug into the new one
Plug the harness into the refrigerator, slip the new maker over the top screws, with the water feed tube inserted into the maker
Install bottom screw into the bracket that holds it in place.
This took less than 5 minutes.

Followed the online PartSelect video instructions and it was very helpful. The ice maker has to cycle through before it starts making ice so don't be alarmed when nothing happens when you first hook it up.

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve

I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.

Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!

I took out 1 screw , unplugged the icemaker and lifted it out and installed the new one and had ice in no time at all. can't get much easier.

Loosen the screws on the sidewall (don't take them all the way out and drop them on the floor as I did) and remove the screw from the bottom bracket. Change out the electrical wires and the wire level sensor that does not come with the new unit. Put the new one in place and give it some time to cool down and make ice ( don't be impatient like I was and think the new unit was bad or that you replaced the wrong part)

I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.