ASD2120DRW Admiral Refrigerator - Instructions

I watched the instructional video included with the shipping date e-mail(about 3 minutes long), and simply followed the instructions. It took about 2 days for the refrigirator section to return to normal cool temperature to the level set.

Followed the instructions from the excellent video by Steve on your website which made the installation easy.

All you need is a 1/4" nut driver or a 1/4" socket and ratchet. Remove the plastic cover to the freezer fan. remove cover to light fixture, bulb, pop out the light socket and remover 2 wires. Remove Ice maker by removing bottom screw and loosing the top 2 screws then lift up and out the ice maker enough to disconnect wiring harness. Revove 4 screws in back panel and the panel can be moved foward. Remove 2 screws holding the fan to the panel. Lay the fan on top of the cooling coil and remove ice maker electrical plug and the panel can be removed easely. Both the heating coil and thermostate switch are easly excessable.

Replaced the "Run Capacitor. The non-rythmic clicking associated with the compressor coming on continues. The problem was obviously not the Run Capacitor". I don't know what to do next. Any suggestion would be appreciated.

Thanks,

Phillip

Removed two panels from inside the freezer. Unplugged the defrost element. Worked the wires around the styrofoam support for the evaporator. Removed one wire clip that held the heater in place and removed the heater. Reversed the removal process for the installation of the new element.

I went online to PartSelect to see how much I'd expect to pay for the ice maker assembly if I called an appliance repairman to fix it. Instead I found an awesome, very well described video on how to do it myself. I ordered the part and paid ground shipping, but received it the next day!! Installation was a breeze (except I got help removing the electrical jacket because it was an awkward angle and I was afraid that I would damage it). The experience did as much for my single, 55 yr. old self esteem as it did for my wallet. Thank you PartSelect! I'll be back!

Repair was very easy. I watched the video and read the descriptions by other customers and it was just as described. Had ice again in about 4 hours and has been working great since.

(1) Watched the PartSelect installation video. (2) Placed Order. Arrived in two days, regular delivery. (3) Opened package. (4) Selected installation tool. (5)Removed old Ice Maker Assemply (6) Replaced w/new. Ice in a couple of hours. Video & order/delivery aside, the entire process took less than 10 minutes including selecting tool and opening package. PartSelect video very helpful.

No instructions with part. Found a picture on line and changed the arm, but it didn't fix the problem. Fairly easy after figured out what needed to be done to get to the part.

After watching the video witch was GREAT help THANK YOU

The Amana's Ice Maker mounted against the back wall. I'm a 61 year old female that ordered this to help my aging parents. The wire harness only unplugged from the Ice Maker and was hard wired to the Frig. I had to "blindly" try to depress and release the harness clip and that took most of the time. When putting in the new ice maker, I noticed that the opening for the fill tube was now against the wall and not to the back. So, I had to disconnect it again. I found that it is also made for a side right fill by cutting out a perforated tab. Just to make sure there wasn't an overflow out of the other round hole, I used silver tape to plug the hole. It took two hours after plugging back in the frig and turning on the water supply before it made ice.

Kids complaint no ice and smelled like burned plastic,found ice maker melted,Replaced ice maker assembly,used existing harness not supplied with new unit,ice maker still no ice,verified an open at fuse link,installed inline fuse in place of existing fuse link.I was told harness not available.Harness section should be on new unit.Hint Hint!

Ordered replacement icemaker from PartSelect.com. Upon receipt of part installed part as per the online video. All went well. Whirlpool rep. stated that the icemake works well when the freezer temp. is set at 10 degrees or less.It took appreximately 24 hrs.for the icemaker to fill the bucket with fresh ice. It would hace cost approximately $230.00 or more if I had called a Service rep. to do the job. So I elected to do it myself.

well, my problem was the dual water valve. I check the two water valve connectors, one was good ( yellow ) and the other connector (brown) was bad. I tested them both with an ohms meter, of course all power was off. I think when ever there's a problem with not receiving ICE this should be done before replacing the ice-maker for there's a lot of things going on in this area. The Brown Connector releases the water into the ice-tray (that tested Bad with a reading of 257 from ohms meter,and the yellow had a sound from ohms for full contact a good reading. The brown valve was bad.

Mine was alittle different than the online instructions. 1. I removed the motor. 2. I took the fan off the old motor and cut the wires about 3" back from old motor. 3. Mounted the new fan on bracket and put the fan on the new motor. 4.connected wires that were cut and used wire nuts to connect. 5. Mounted bracket and motor/fan to unit and it works like its brand new. Thank you PartSelect!