AS2125SIHW Maytag Refrigerator - Instructions

removed 4 screws, reeplaced broken ice door,
replaced 4 screws. Easy job with your site diagrams.

Removed approx. 5 phillips screws to access the flap from the outside of the freezer door and R & R'd the flap, then repaced the screws. Fairly simple installation. Most impressive was how easy it was to find the part here and the quick delivery.

Removed 6 screws to get at broken part. Had to remember the disassembly sequence to properly reassemble. The whole process was relatively simple. I saved about $125 which would have been the cost of a repairman coming to the house.

First remove srews from front icewater panel
Second pushed panel up to remove and disconect electric conection.
Third rmoved broke ice door and installed new one in holder frame.
Fourth reversed steps two and one.
Job cpompleted.

First I removed spill tray. It slipped right out. next I removed the front cover.it had 2 screws hidden by the spill tray. next were the 2 screws holding the selection slider.Under it is 3 more screws after removing them then the assembly will come lose from the refrigerator.Be careful you dont drop the ice door. unplug the assembly. Turn unit over and you will see the limit switch remove and replace it with 1 small phillips screw. remove and replace dispenser actuator pad.replace everything in reverse order.The ice door is the only thing a little tricky.still i replaced ours in about 10 mins.

Removed old ejector arm and installed new part.

Emptied the door by taking out all the shelves with their contents. Removed the upper door closer works. Removed the door by lifting up and away from the main box. Layed the door on its side. Took out the old lower hinge pin and door closer with cup. Put in the new lower hinge pin and door closer with cup. Applied sewing machine gear grease to the 2 pieces where they work together. Lifted the door and placed the lower hinge pin into the door closer with cup. Replaced the upper door closer works.

Disconncted power, pulled plug on disconnect, loosened 3 ice maker attach screws, removed ice maker. carefully removed old broken part, to understand reasembly. Reinstalled new water fill & bearing part.. hung icemaker and tightened attach screws. Reattached electrical plug.. turned on power, it all worked. .took about 45 min to remove, 15 min to reinstall. Right tools needed re disassembly AND ASSEMBLY

ordered a new shut-off valve. arrived in 5 days. installation had to wait a couple more day for i had to order a new compression nut. the reason i had to order a new nut was because the original nut was made of teflon and stripped easily when i tightened it to make a leak proof.joint. the new nut arrived in two days and was installed readily being that it was made of brass and consequently did not strip when i tightened to make a drip proof joint. finished in approximately twenty minutes' the video that this site has on the internet was of great value.

I switched the ring and still had the same problem. What caused the Drive ring to crack was the Ice maker drive was cracked also, when it filled with water it would tip. The ice was not freezing completely and would cause the ice to build up and the auger was froze with ice or a big piece of ice would jam it. So I replaced the Ice Tray, it is working like new. I have to buy another ice tray as inventory, although I know inventory is bad but I never agreed with that theory.

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

follow video

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

Popped out the old switch and replaced it with the one dying

Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.