Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
I needed drip bowls that fit properly
I ordered gray enamel drip bowls and they fit perfectly. Unfortunately 2 of them were chipped and bent slightly. They still worked which was better than the make shift ill fitting ones that came with the house so I decided to keep them. I did tell parts select about it and they sent me a new order of drip pans at no charge. I used the perfect ones but the 8" drip pans flaked off paint after one use. I guess this is an Amana defect...the paint doesn't stick under heat.
The Baking element in the bottom of the stove apparently shorted out and partially melted
First I turned off the circuit breaker on the house electricity panel. I removed the two screws that held the element in place in the oven. There were two wires connected to the element by spade plugs that were free floating in a fiberglass pad. I reconnected the spade plugs and put the element back in place and put back in the two screws. This procedure had I known what I was doing could have been done with the stove in place and would take no more than 5 to 10 minutes. Having no experience at this, I had pulled the stove out into the room and also removed the back cover which turned out to be unnecessary. I put everything back in place and held my breath and turned on the circuit breaker. Voila! It worked!
Getting F 1 and 2 error codes and the oven turned itself off.
Really easy but in this model there are 2 versions of the sensor, male and female. The website didn't have any place to see that. So the first sensor that came was male but we needed the other. After calling they sent me a return form and sent the new part (which was actually much cheaper) overnight and it went in very quickly. Would check this out again when anything went wrong. they are great folks to work with.
The oven light has been broken forever-I turned on the oven and the element started flaming.
My husband replaced the bake element in moments. We couldn't get the broken light out of the socket because we couldn't locate our needle nose pliers. After a few days I finally got tired waiting and found a small pair of pliers in the house and got the remains of the bulb out and screwed it in, and plugged it in and we're in business! Never wait for a man to do what you can do yourself! I was so pleased that ordering the parts on-line was so easy and I didn't have an expensive repair bill to pay!
This purchase was for replacement parts, not for repair. Installation was a simple matter of taking out the old and installing the new, which is extremely easy to do. One item was damaged; Parts Select was absolutely fantastic to deal with regarding replacement! One word of caution regarding the product - I mistakenly ordered Whirlpool drip pans which have an opening in the bottom, the Maytag pans don't. Initially I thought that it was a mistake by Parts Select; which wasn't the case. The pans fit perfectly so I kept them. If I reorder, I will be certain that I order the correct pans.
After trying for many years to buy the "cheap" drip pans in the store, "They never fit right", I decided to order the correct drip bowls. Now my stove top looks brand new, and my coil elements fit the proper way.
One burner didn't work all the time the other would go red hot
I unplugged the stove from the outlet, then removed the two burners I was going to be working on and the drip pans. Then I raised the top part of the stove and removed the screws holding the plug-in blocks to the stove. Then I cut the two wires going to the old plug-in block and stripped the wires back to match the new wire parts. Then I placed the sleeves over the new wires, then I placed the new wire beside the wire I stripped on the stove and screw on the wire cap making sure it was tight. I repeated this three more times, once I had all four wires connected I then placed the sleeves over the connections and heated them up until they were formed around the connection. Once I had all the connections done I placed one wire at a time into the plug-in block until it locked into place ( I looked at my old plug-in blocks first to make sure I placed the new wires in the correct way ).I then used the metal mounting bracket that matched my old ones and snapped the correct one onto each plug-in block. Before mounting them onto the stove I compared them to my old ones to make sure they were correct. Then I used the new screws to mount them to the stove. I took a second look at everything I had done before closing the top cover of my stove. After lowering the cover back into place I put both the drip covers in place and then installed the burners.I then plugged the stove back into the outlet and tried the burners. This was very simple and the video on the web site shows this very well which made my job very simple.
Pulled the power plug. Removed all the screws holding the back of the range in place. Checked all wiring to make sure there were no burns, cracks, or other problems. Removed the output wire from the thermocouple, reinserted the power cord and checked for voltage. Removed power cord, then removed the 4 screws holding the control in place. Removed all electrical connections, making sure of where they went, then installed the new control. While still hanging loose, put the power plug back in and saw the time light up. Pulled power plug, put everything back together, put the power plug back in, shoved the range back in place and the owner proceded to bake an anglefood cake. All is well.
un-screwed 2 scrws and pulled out the old one and pulled off the 2 wires put the new one on the floor of the oven and hooked-up the 2 wires and pushed it in the back wall and replaced the 2 screws! done maybe 5 minutes
first I unplugged the stove,took the screws out of the pan that holds the element to the stove, then unplugged the element.then I plugged in the new element, then screwed the screws into the pan that holds the element into the stove. it was very easy.
1. Slide the Oven door out of its hinges after removing the screws - see Owner's manual. 2. Place door on floor with the inside face on the floor. 3. Remove screws on side and bottom of door and the lift away the side stamped pieces. 4. Remove screws as they becom visible and lift away the pieces till you reach the inside glass.
Remember the sequence and be careful not to strip the Phillips screws when unscrewing.
Oven never came up to correct temp. Broiler did, so it had to be the bake element.
Turned off the power! Unscrewed the element (2 screws) pullled the wires out. Put the new part right in. Easy! Thank you-only a week before Thanksgiving, what a life saver! Also, order on Monday AM and was delivered by mid-day on Wednesday!