Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ARG7302WW (P1143337NWW) > Instructions

ARG7302WW (P1143337NWW) Amana Range - Instructions

All installation instructions for ARG7302WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ARG7302WW
211-225 of 257
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Gas took very long to turn on and failed to reach set temperature

  • Customer: John from Seattle, WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Set masonite under feet, removed drawer, and pulled unit out from wall. Disconnected electric and turned off gas supply at wall. Reached in where drawer was and disconnected 2-wire igniter connector. In oven, removed cover in bottom by sliding it off, then undid center bolt on V shaped plate covering igniter and burner. Undid 3 screws holding igniter bracket and pulled through the disconnected wire harness. Removed igniter from bracket carefully as it was held in quite tightly. Carefully slid new igniter in bracket, fed wire in back and replaced 3 screws holding in igniter. Reconnected wire under unit, replaced V plate. Turned on power and gas, tested and gas lit right away. Reassembled the rest and pushed it back against wall.

Light burned out in upper oven

  • Customer: Shirley from Las Vegas, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Screwed in light bulb and glass protector

Oven Will Not Heat To Temp Setting

  • Customer: JOSEPH from RACINE, WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug power and turn off gas valve. Lower drawer removed out of way. Tilt back stove. Layed piece of wood under front with wife makeing sure not to fall forward. Remove back plate(2 screws)you will see the plug in. Unplug. Go inside of oven remove (1screw)bottom plate. See(3screws)remove igniter assy. Pull old out,replace new one (may have to pry bracket apart just a bit to slide in).

Lower Bake Ignitor would glow, but would not ignite flame.

  • Customer: Robert from Sapulpa, OK
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
First, my wife and I pulled out the oven from wall to disconnect electric plug and, also with a wrench; I shut off the gas connection on the wall. I then removed front door of the oven by pulling up on door to have easy access to lower part of oven, and then removed pan to get to Igniter. Removed the three screws on cage that supported the Igniter and, I also had to remove several screws to the manifold and bottom pan that supports the manifold so that I could disconnect Igniter. I then was able to pull out old Igniter and, reconnect the new one. After that, I reinstalled everything in reverse. Before pushing oven back into wall; we made sure the new igniter worked. It worked just great. My wife and I were so happy and proud that we done it our self, and not have to call someone to do it for us. It took me and, my wife about an hour and a half to complete the job. I believe the reason it took us as long as it did was because we really didn't know what to expect. Now that we know; I am sure that we could do it again in 30 to 45 minutes. Dave & Marsha; 8/23/2013

Oven igniter would not ignite the gas

  • Customer: Robert from Logan, UT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
To access the igniter (bake, not broil) I removed the oven racks and removed the pan at the bottom of the oven enclosure (which just lifted out, not secured by any fasteners). Using a Phillips head screw driver, I removed the three small screws that secured the igniter and its shield to the burner. I then pulled out the drawer at the bottom of the oven, looked to the back of the space under the oven, located the igniter connecting plug and disconnected the igniter lead. I was then able to pull the igniter lead wires and plug through the hole at the rear of the oven and remove the igniter from the oven. This can all be done without moving the oven, I just laid on the floor and reached under the oven to disconnect the igniter lead connection. Once the igniter was out of the oven, I carefully removed the igniter from it shield by gently pulling the shield off, there were no fasteners to remove. I installed the new igniter into the existing shield, being careful not to touch or damage the delicate heating element on the igniter. Re-installation of the igniter was just the reverse of the removal process. The whole thing took about 15 minutes for this model of oven, even though I had never replaced an igniter before.

Broiler & burners worked, oven would not ignite or heat up.

  • Customer: Mary from Weston, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Roommate did the repair..so I don't know. I did the research online, the igniter solved the problem. Saved us buying a new oven!

gears and gear box top case cracked

  • Customer: Willliam from Goldfield, IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Take top cover off take gear box cover off. check all gears for wear and clean all of above. Be sure you identify all parts needed before you order plus assembly grease!

Stove Range Drawer Difficult to Open and Close

  • Customer: Hau from Burke, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Insert one end of the railing into the slot in the back of the stove. Align the front end of the railing with the hole at the front of the stove. Align the roller with the hole. Secure the front end of the railing, roller ,and hole with the shoulder bolt using a 10mm wrench. Tighten just enough but don't over tighten.

2 burners not igniting

  • Customer: Peter from Eagan, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the burners 2 screws per burner disconnected the wires to the burners. Lifted the oven top off removed original ignition module. Installed wires to the new module taking note of replacement location. Than mounted new ignition module. Tha only hiccup was dropping 1 screw down into the stove lining found replacement screw and installed module. Cleaned and replaced top. Mounted burners and the stove is working like new. Project proved to be quite simple and guick. Thanks to partselect for there prompt delivery and other peoples input on install made it quite easy and simple,

When the oven would cycle there were mini explosions and the burner was very noisy. A trouble shooting manual said that this was most likely due to the oven igniter not getting hot enough and gas was accumulating before it finally lit.

  • Customer: Brian from South Talkeetna, AK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
1. Remove the oven bottom inside the oven. 2. Remove the pan underneath the oven bottom by undoing one hex nut. 3. Once this is done the oven igniter is visible. It is located in a protective housing. 4. Remove the three sheet metal screws that hold the igniter housing in place. 5. To unplug the igniter remove the storage door. Underneath the oven there is a access panel. Remove it by taking out the two sheet metal screws. Once this is removed the igniter can be unplugged. 6. Pull the old igniter out of the housing and carefully install the new one in it. Careful the ceramic igniter is fragile. 7. Plug the new igniter in and screw the housing back in place. Changing the igniter was easy once we found the panel after removing the storage drawer that made it possible to unplug the old igniter and plug in the new one.

Bulb Replacement

  • Customer: Judith from Phoenix, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Oven not lighting, sometimes would light, but took a long time.

  • Customer: Jerry from Crystal Falls, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Inside the oven: Pull the bottom floor pan off, just lift up in front and pull back.--Then take the one hex nut off the burner diffuser and lift off.--Remove under storage drawer. On Bottom of oven (Underside): Take off plate in back (2 ea screws) so you can unplug wire to igniter.------Go back inside oven and remove the 3 ea. screws that hold the igniter and holder/guard in place.-----Pull the igniter out.------Replace the new igniter in the holder/guard being careful not to crack the igniter.------Reverse procedure to re-install new unit.

The oven igniter was burned out so the oven would not light.

  • Customer: Jeff from Minneapolis, MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the bottom cover and the heat shield, then removed the screws that hold the igniter mounting bracket. After removing the drawer and the wiring cover I disconnected the igniter wires. I then removed the igniter and mounting bracket, pulling the wires through the hole at the rear of the lower burner box. I installed the new igniter by reversing the process.

stove sometimes would not light or took really long and did not maintain heat

  • Customer: Patricia from Milwaukee, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
We unplugged the stove and turned off the gas. We slid the oven door off just to make it easier. Unscrewed 3 screws holding the igniter in place. Pulled the igniter out from the back of the stove. Disconnected the two wires. Slid the new igniter in the holder. Rewired it and slid it back into place. Put the screws back in and it was done. Plugged it back in, turned the gas on, tried it out and presto! It was perfect! Lit immediately and strong and now i have a brand new 20 year old stove. lol Happy girl! And this was done by 2 50 year old women!

Oven not working but broiler is functional

  • Customer: Drew from Camano Island, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Since the broiler was operational, this indicated the gas valve was probably functional since it provides gas to both the broiler and oven. I ordered the igniter based on other recommendations because the gas valve will not open until the igniter is drawing adequate current. This fixed my problem.
All Instructions for the ARG7302WW
211-225 of 257