ALW880QAC Amana Washer - Instructions

1. unplug unit 2. remove front access plate 3. disconnect tension spring on drive belt 4. remove 4 motor mount screws 5. disconnect intake and return lines from pump using a pliers to decompress compression rings and sliding lines off. 6. Manipulate motor and loosen drive belt from bottom of tub and let it hang. 7. tilt motor bottom out exposing pump and remove 3 screws using TREX head driver and remove pump. 8. install new pump

First removed all screws with a nutdriver then lifted the body from the base. Removed the two hoses at the pump (be ready for excess water). Removed the 9/16 bolts (4) to drop the motor assy. I also took off the two front balance springs to have easy access. I at this point was able to remove the pulley and put new belt & pump on the motor. Remember to watch carefully to align belt. removing the idler pulley is a no brainer. Took about 45mins. to complete, a no pro job!!

took the belt out and took the thing out and fixed then put it back.

Very easy repair. Removed the lower front panel of the washing machine (two screws) with nutdriver.

Removed hose clamp with pliers. Removed hose from machine. Replaced hose and ran thru a full cycle to check for leaks.

No leaks, back in business in under an hour. This time includes going out to garage and gather the two tools needed for the job and cleaning up the water that came out of the hose during the removal process.

I unplug the power plug, turned off water supply and unsrewed the water lines connected to the clogged valve.I unsrewed six screws on the front of the washing machine and took the front panals off. lifted the the washing top and replace the hose and intake valve, which was shipped to me. put the top down and put the two front panals. reconnected the water supply to the new valve and turned the water back on. connected the electric plug.works as good as new.

It was so simple I don't think I even need to explain. Couple of screws in and out and done. Saved big money by doing the repair myself...I was surprised how quickly the part arrived. I was able to access from the back of my machine. Did not have to remove the top. Very easy thanks

I read what the others had done and thought it was the lower bearing so I originally tore it down and replaced just the lower bearing.

Unfortunately, after 2 + hours of doing that and putting it back together, it still didn't fix the problem. So I read more reviews and others claimed to use this kit and that it fixed the problem. So I ordered the kit.

BTW, Parts Select rocks!!!! They get me the part within about 2 days every time.. Great Service! Thanks guys!

Anyhow, part came in, knowing how to tear this thing down now, I was able to get to where I needed to be within about 45 minutes.

2 things that were difficult.

The first was removing the plate at the bottom of the tub. This is the aluminum plate that looks somewhat like a spoked wheel. Maytag has a tool for this. Without it, you must go at it with a small punch on one of the spokes and carefully tap the seal until it turns. You may have to try it from different angles to loosen it up but it will eventually give way..

Once you get that off, the second little piece of joy is actually removing the seal from the bottom of the tub. Here again, Maytag offers a tool to remove this. Without it, and with years of this rubberized fitting mounted in this plastic tub and corrded with water and crap... you will need to create a bearing puller.

I did so with a 2X4 board straddled across the bottom of the tub. I used an 8 inch lag bolt, drilled a hole through the 2X4 and placed the lag bolt throuigh the board and through the center of the bearing. I attached a large washer and nut to the bottom side of the bearing and then began to tighten the bolt on the other side of the board. By tightening the bolt, the board created alot of tension but not enough still to seperate it from the tub. With the tension on the bearing, I turned the tub over and tapped it with piece of wood the size of the bearing and a rubber mallet. It popped right off. The rest was just reassembly.

Don't forget to remove the sticker backing on the felt gasket to hold the gasket in place while you screw the tub back together...

The good news... Super quiet! So, about 3 hours.... (I had to come up with the idea to remove the bearing and build it) and it's all done..

Yeah.... Fun Saturday.

I found about 2-3 baby socks stuck in the pump and couldnt remove them so I had to replace the part. Unfortunately I found this website AFTER I took the bad pump off. So I ended up removing the lower front panel and then flipping the washer upside down and removing the bottom of the washer and taking the pump off because I couldnt see any other way to get it off. The new pump arrived very quickly and I put it back on and put the bottom panel back on and flipped the washer back right side up. I certainly made it more difficult then it had to be but it was still fairly easy. Now I see all I needed to do was remove the motor to get the pump off. Oh well.

simple as removing front panel from washer held on by two screws and the hose was right their. Took a few minutes to disconnect it from the pump and pull it out through the rear, then feed the replacement in and reverse the process. Piece of cake. Thank you.

After turning on the machine set to the spin cycle and acertaining that the problem was not a switch or the motor the lower cover was removed (Two sheet metal hex head screws)with appropriate socket. The failure of the belt was self-evident, having sprayed itself in granuals, the belt itself having parted with easy removal.
A search of the internet produced the order for drive belt, which arrived in a timely manner trough Fedex.

Replacing the belt was the most labor intensive part of the process. No mirror being available a CD was placed in the base of the machine in order to view what fasteners (Three torx head) fasened the pump to the motor assembly. Removal of the pump was necessary in order to replace the belt.

The removal of the fasteners required that three holes (120* angular spacing, 1/2" diameter, located on the pump fastener bosses) be drilled in the machine base in order to
remove and replace. This required setting the machine on its side. (Tell the engineers to put an inspection plate there in order to negate having to drill the holes. Thankx.) Pump assembly was lowered off driveshaft and belt replaced. Tensioner set on belt after pump assembly fit to driveshaft and torx fasteners replaced and tightened. Machine powered up, checked for function. In use. Lower cover replaced. I'll be using your buisness for parts again, no doubt.

I takened the 4 bolts out of the motor assimbley, and droped the whole thing out where I could see the screws that held the water pump on, and I took them out, and lifted the water pump, and put the belt in place, and the new pully on , and the new spring in place. Then I reversed the proseger.
It works like a new one.

This washer was "professionally" repaired six months ago....that being said, I found two of the three Torx screws holding the pump to the motor to be lying inside the cabinet. This allowed the pump to move and wallow out the seal. Replaced the pump and replaced the screws correctly. No leaks, no problems. Pump is an exact replacement from PartSelect and ease of installation was no problem. Would suggest if you are going to replace the pump, order the three screws and replace them too.

Screw broke lose in agitator from drive bell stripped (plastic) for transmission gear. Received new Drive Bell and had to lightly cut out old from Agitator housing with saws all, cleaned years of soap build up on steel spline with wire grinder, lubed the Drive Bell inter and pounded on to spline gear with rubber mallet, I thought a bit too much force but what the heck I landed to the same bearing point as before. Work Out Great.

Water inlet valve was different than the one shown on web photo. The hose supplied was the wrong size so I had to use the original old hose. Wire harness had to be modified since the electrodes were on opposite sides of the valve. Overall I was disappointed with the part and the service.

Unplug and disconnect Power, Drain and h20 connections. Removed front panel, disconnected internal electricrical connections and capicitor from washer. Remove 11 (I think) screws connecting outer cover to base. Remove pull drain hose through the outer cover and hold the end lower that the washer to drain the excess h20. Remove the hoses from the pump and outer tub. Remove outer cover from base exposing the guts. Grab the bottom of the agitator and pull up pretty hard. Agitator will pop off, watch your head. Remove the 4 bolts attaching the Inner tub to the hub. Remove seal from top of transmission spline. You will need a 38mm deep well socket to remove the nut from the top of the transmission. I used a socket and a impact wrench to remove the nut. Remove the teflon seal that is below the nut. You will need a puller and/or grinder to remove the hub from the transmission spline. My puller broke, so I ended up using an air grinder to cut a couple of pizza slices out of the hub. Then I used an air hammer to break the slices off of the hub. Once it is cut the cast aluminum is quite brittle. Pull what remains of the hub off of the transmission spline. Remove the bolts that connect the transmission housing to the outer tub. Remove the 3 bolts from the underside of the outer tub that connect the outer tub to the upper bearing. using a set of vice grips, grab the top of the springs that connect the outer tub to the base and carefully remove them one by one.
The outer tub should slide right off. Remove the bearing from the transmission. Supplies that you will most likely need are the 3m800 sealant, when you get this you will only need a little around the bottom of the lip where the new seal attaches to the bottom of the outer tub. You will also want to get the Seal tool which will ensure that the seal that goes around the top of the transmission spline is seated properly. Assemble in reverse order but keep in mind to attach tub bolts prior to attaching the springs. Also keep in mind that both maytag and amana make a washer with the same model number LWA80AW. Check to see which one you are ordering for. The kits are different. Don't ask me how I know. Just make sure you get the correct kit the first time, it will save you a whole lot of head scratching.