AGR5835QDQ Amana Range - Instructions

Open the oven door, take the bottom out. The ignitor is right there!! unscrew it and unplug it... plug in and screw in the new one! Took about five minutes!! Our oven worked again after not working for a year!! Yeah!!

Removed oven door (slides out). Removed side and bottom screws from frame and slid new glass into place. screwed in the 8(or so) screws.

Suspected the igniter, and verified by reading comments on your parts site. The mounting screws were frozen so I used larger screws. Piece of cake! Wa La!

shut off gas and unpluged stove pulled it away from wall removed(2)screws from (top left inside oven)unpluged old sensor in back(left side)and pull old wire thru feed wire from new sensor thru hold pluged in put(2)screws back in done(***used drinking straw and tape to feed new wire thru hole***)

The broiler igniter and oven igniter are the same - WITH ONE MPORTANT DIFFERENCE- the plug! I tried to just switch them since we dont ever use the broiler but could not, due to the plug. I think that is part of planned obsolescence ! Anyway, I left the door and the power on - you guessed it, rebel! If you get a tingle from replacing this part you shouldnt be trying to fix it on your own! I removed the oven racks, took two small screws from rear of oven floor out, removed base plate. Two more small screws released the defective part. Pulled the plug wire through the back of oven and unclipped the connector. Plugged new part in, tucked the wires back into the insulation, replaced two screws on the igniter. Test fired oven- worked like a champ. Shut burner off, reinstalled base plate and screws and put the oven racks back in. Easy!

The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.

Followed the instructions that were provided me when I ordered the Gas Oven Igniter

Bought the igniter, replaced it with the old one and it works great.

It was really easy. Watched a brief tutorial on the Internet and went to town. Followed the instructions and had a working oven in no time at all.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

replaced igniter with screw driver

I followed the instructions on this website. Luckily a friend showed me where the sensor was located and from there, it was a breeze. Removed six screws on the back oven panel, removed two screws inside of the oven, took the old sensor out and put the new sensor in. Voila - works great. I can't tell you how much I appreciate Parts Select and the feedback and help from the customers. I've been out of work for almost two years and when I called my repair guy, he said it could be the computer and that would be expensive. That's when I searched on line and found Parts Select. I would have never even attempted this on my own if it weren't for you and it was so simple. Next time anything goes wrong with an appliance, I'll be contacting you first! Thank you.

bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!

I tried to take it out from the inside as the vidio shows. But it would not come out far enough. I pulled out the stove and removed back sheet metal panel. Unpluged the electric, Unhooked the temp sensor,pulled it out from the oven side. Put the new one through the hole,and rehooked it up. And got to clean up the dust and my missing oatmeal I spilled a while back. Turned it on. Checked it with a spare temp gage. Works so far.

The website helped me to troubleshoot and identify my issue. They had a complete database to find my part and some instructions to how to install it.The repair was easy: 2 screws to remove at the bottom of the inside oven to remove the large plate. Then 2 more screws to remove the ignitor. Now to unplug the ignitor, I really had to access the back of the stove. i saw videos of people doing this from the front under the stove (not moving it). In my case, for this model, I had to move the stove to the "middle of the room", to access the back. Then 2 more screws to remove a small plate where I could see the cable to unplug.It was advised to close the gas faucet, and unplug the stove. I only unplugged the electricity, and it was fine. Then I tested the repair before I put back the large plate at the bottom of the oven.My only issue was the isolation "tube" going around the 2 wires ad connected to the new ignitor. I had them on my previous model, but not on the new model. So I managed to put it back to cover/isolate the new wires. Then everything worked again.