AGDS902E Amana Range - Instructions

Un plug elect. Cord. Remove door by pulling upward removed back stove panel, un did 2 wire nuts leading to igniter. Un screw igniter inside oven at top next to burner pad. Interchanged old ignitor with new plug stove back in. Thats it.

The earlier reviews said very easy and 15 minutes for beginners. They were right on, except I could not get the old screw out no matter what I tried. I eventually had to drill it out and put in a self tapping new screw. This was a first for me. Then it took 15 minutes or less and works fine again. Hopefully next time someone will tell me how to get that old screw out faster.

First I removed the knobs on the range, then the front cover and then removed the two screws that hold each burner in place. I removed the top and removed the Module and started replacing the burners and front ocver and knobs. The Module worked GREAT. Thanks for your fast service in getting me the parts.

Removed the top, 4 screws and pulled the contact wires off. Replaced the module and connected the contacts. Put back the screws and the top. When the stove was new it did not operate properly and we had a technician out, but naturally it worked for him. For the past 14 years intermittent operation has been agravating me. With the new module the burners have never worked so well.

Removed two screws and disconnected the ignition wire. Then connected ignition wire to new burner and installed two screws

Replaced the existing ignitor by removing the bottom drip pan/gas line/ignitor (apprimately 18 screws), unscrewing the wire nuts, removing the old ignitor, connecting the wires to the new ignitor, and reinstalling the drip pan/gas line/ignitor (18 screws).

Wow, ordered the part here and it arrived in 18 hours!! Job was fairly straight forward but the screw holding it in place was corroded and stuck. Several heating and cooling cycles with a torch and some spray lube and lots of patience and I finally rocked the screw lose.

No problem removing the burners. Removing the old initors was a different story. The tiny screws that hold the ignitor in place were baked in and could not be removed with a screw driver. I drilled them and tried to use an easy out to no avail. The screws are very short so I had to use care not to drill thru the burner. Both screw heads did snap off. I resorted to a hi temp epoxy to secure the ignitor flanges to the burner and now the all burners ignite as designed.

I slid out the oven burner disconected the old igniter and replaced it with the new one & slid back in place and connected the two wires and I was back in business. The job was relativly an easy one.

For the third time in less than a year I had to replace the broiler igniter. The range is 27 years old and has given us excellent service. When the igniter failed it's replacement lasted 3 months. The next replacement lasted about 6 months. This last replacement has been in service about 1 week. We shall see. The last one had an open wire within the ceramic mould. There was continuity from one wire, through the black portion, but not to the second wire. It seems like it was a fault in manufacturing.

Easily replaced the stovetop burner bowls by removing the old ones and replacing with the new ones.

Parts Select provided easy online ordering and was nearly one-half the price of other online suppliers.The quality was excellent!

Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You

Unscrewed all the phillips screws holding the door together. Re-assembly indicates that you want to note exactly how the sides overlap the front and back steel panels, possibly take a cellphone picture before starting. The front and back panel will bend down the bottom attachment metal tabs, misaligning the sides, etc if you replace the glass with the door still on the range. Prob. best to have a second standing by or remove entire door first.

removed two screws from each burner, removed ignitor wires from burners, pulled range top removed old module and inserted new reattaching wires for four burners, switch and power to new module. reset top, attached wires to burners and reinserted screws

Removed burners and top cover to access ignition module.
Remove and replace module and reassemble stove.