Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AGD4475TQ0 > Parts

AGD4475TQ0 Admiral Dryer - Parts

All parts for the Admiral Dryer AGD4475TQ0

Below is a list of all parts for the Admiral Dryer AGD4475TQ0 - Residential. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the AGD4475TQ0
1-14 of 126
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.56

Multi Rib Belt - 92-1/4"

This multi rib belt is an important part in your dryer, it is what helps rotate the drum. The belt attaches to the drum, idler pulley, and motor pulley. As the armature of the moto...

$14.81

Door Switch - 3 Wire

A door switch is a simple on/off switch mechanism that prohibits the dryer from operating when the door is open. This part may need to be replaced if you find that the dryer is not starting, will not shut off or the door will not close properly. All you will need is a putty knife and a Phillips screwdriver. Pry open the top of the dryer, remove the two screws underneath the lint collector without removing the entire thing, unplug the switch, remove the screws that hold the switch place, take out the old switch and install the new one by screwing it back into place.

$14.96

Thermostat, Internal-Bias

A cycling thermostat is in tune with the temperature of your dryer and regulates it in order to maintain a certain temperature. This thermostat reaches a temperature of 155 degrees...

$21.73

'M' Series New Style Coil Kit

This is an M series new style coil kit, used in gas dryers. When the igniter reaches a high enough temperature, these coils work together to let the gas enter the dryer. The coils open the gas valve; if the valve does not open the heating element will not ignite. Both coils must be operational for the valve to open. This is a safety mechanism to ensure that there are no unsafe buildups of gas inside your appliance. This kit comes with a three-terminal boost/hold coil, and a two-terminal main coil. Each part is approximately 1 1/4 inches in diameter. If the igniter glows but shuts off without igniting gas, it means one of both of your valves is faulty. We recommend you replace these as a set. Before you begin this repair unplug your appliance and shut off the gas supply.

$17.97

Igniter Kit

If your dryer will not heat, takes too long to dry, or does not provide enough heat, you might want to replace your igniter kit. This silicone carbide igniter with ceramic holder k...

$5.76

Tri Ring

If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.

$27.70

Radiant Flame Sensor

If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor...

$5.84

Leveling Foot

If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Keep the washer as close to the floor as possible. Your model might have rear legs that level themselves, or it might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This replacement part is sold individually.

$29.24

Drum Felt Seal

Includes adhesive.

$15.89

Switch, Push-To-Start

This push-to-start switch activates the dryer when the button is pressed and released. If your switch is not turning on or off, will not start, or the contacts inside the switch are shorted out, it is best to replace this part as a possible solution. Remember to unplug your appliance before beginning the installation process, as safety precaution. For installation instructions and accurate guidance, refer to the diagram provided by the manufacturer.

$20.20

Wheel, Blower (Includes Illus.

The blower wheel is a squirrel cage type wheel whose purpose is to move the air through the room or appliance.

$30.80

High Limit Thermostat

This hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this piece will shut down power to the heating element. NOTE: As per the manufacturer this part has been updated, may look different but will function the same as the original.

$6.19

Lint Trap Housing Seal

This is foam seal for your dryer. It forms a seal to prevent air from escaping the rear of the dryer drum and the lint duct. This model comes with adhesive backing and is located i...

$30.53

Two-Piece Split Ring Bearing

All Parts for the AGD4475TQ0
1-14 of 126