Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Pin for drawer lid broke off
Empty drawer and take out . remove glass shelf and front and rear shelf braces. remove 2 screws holding pantry end cap to fridge. remove rear bracket by unsnapping clips. remove temp control arm. and reattach to new end cap. reinstall rear bracket to fridge and align end cap, align screws and tighten. reinstall drawers and shelf brackets. replace glass shelf. and reattach lid to brackets. Open beer and enjoy success.
First pull out bucket, then slide side plastic piece that hides wire harness on lower left side out.. Then pull /slide whole unit forward/out. Disconnect wire harness plug when doing so. Set old unit on table standing on end, put new unit right next to it. remove whole tray assembly from old unit, 3 screws on back. Use new wire harness that comes with new ice maker. put new tray assembly on end unit where the other came off. replace the three screws holding it to fan unit. remove on/off switch from old unit and put in new unit cover. Use small screw driver to remove old end switch cover. On off switch is pushed into place on new end cover. Purple wire on bottom plug and other on top. observe what you have and Just replace what you removed. Piece I did not use was flat plastic piece,flapper? This did not come with instructions, so basically I changed everything incl wire harness, put back together and put back in freezer. Ice bucket was full by next morning. Instructions and or video would have been nice. Tool;s used was a 1/4 in nut driver, small flat blade screwdriver.
Removed the old parts then connected the new parts.
The compressor immediately started when I plugged the refrigerator back in. Around 24 hours later the freezer compartment was at 0 degrees, and the refrigerator was at 35 degrees.
Removed the top glass above the vegetable drawers and slipped the center rail in place. And I would like to add that I would do business with this site again!
We came home from a long vacation to discover a warm refrigerator with its contents in various stages of decay.
Turning the freezer thermostat to its warmest setting then back to cold generated clicks, and after a few tries the compressor started and cooled the refrigerator to its normal cold temperatures. But… later the compressor again failed to start, and everything warmed back up again. With persistence and turning the thermostat up and down several times a day, we could keep the fridge cold.
It was time to order parts. We needed a new start relay and capacitor for the compressor. For our Amana ARB2214CW a start relay (WP12555902) and capacitor (WP65889-4) were listed on the first page of the Partselect parts list for my refrigerator. I ordered them, received them, removed the old capacitor and start relay (which rattled when shaken). and prepared to install my new parts. The new start relay did not match the old. The old start relay fit my wiring which had a single plug with two small female spade connectors in the plug. The new start relay required wiring with two separate female spade connectors; one the normal size and one larger. Phone calls to Partselect and to Westinghouse shed no light on the discrepancy. On the second page of the Partselect parts list was a combination of a start relay and a capacitor (W10613606) that matched my electrical connector. I could see the connection in the photograph. I ordered it and it fit. Easy peazy. That fixed the compressor start problem. Every time the freezer thermostat clicked on, the compressor started. Success.
But… from our troubleshooting we now had a thermometer the freezer, and it was obvious that the temperature difference between the cold point where the thermostat turned the compressor off and the warm point where the thermostat restarted the compressor was much too wide. In addition, the knob was hard to turn and was sticky as it turned. Oiling it fixed the sticky knob problem but not the wide temperature difference problem. I ordered a new freezer thermostat (WP67003000), received it, installed it, and all is now fine with my refrigerator. The new thermostat was physically a little different from the original, but it fit and worked.
I returned the first compressor start relay and capacitor and received a refund including the shipping charge.
Placed new gaskets on hot patio to smooth them out. Took minion bar off and removed door gaskets. Replaced new gaskets, and minion bar. Took freezer door off and replaced gasket. I had problems with the first set of door gaskets but customer service replaced them in record time. Service was outstanding. 5 Stars
PartSelect Number PS8260210 Manufacturer Part Number W10583817
Tools used: Small 1/4 in nut driver Small flat blade screwdriver Needle nose pliers Flashlight Time: about 30 minutes
#1 Unplug the refrigerator.
#2 Pull out the ice bucket.
#3 Slide bottom left edge plastic cover that hides the wire harness out. (To do this you need a small screw driver to pry the front out a bit and to insert into the slot in the middle to unlock it, then pull forward. Be careful not to break).
#4 Disconnect wire harness. (Plug has a small catch in the middle you must press to pull apart).
#5 Pull the whole unit out. (To do this you need to pry a small catch on the left out, then pull. It may be tight since it’s been in there a while and there is a small rubber water tube protruding from the roof that it will rub against).
#6 Carefully empty any water still in the icemaker into the sink. (Try not to get any of the electrical components on the fan assembly wet. If you do, a blow dryer works well to dry out quickly).
#7 Put old unit on a large table and new unit / parts next to it.
#8 Remove ice maker and tray assembly from old unit, three screws on bottom of ice maker. (Do not confuse with the three screws holding the ice dispenser motor in place). Unplug wire harness, remove small funnel.
Replacement Parts Assembly - The next few steps get a bit tricky as you may need to do several things simultaneously.
#9 Route new wiring harness. Route under the plastic clips on the new plastic tray. (Black connector and switch wires run around the bottom left corner of the ice maker head to the front).
#10 Install the new water funnel. Loosely attach new tray assembly to new ice maker ensuring wire harness is routed properly. Plug in the wire harness connectors with the exception of the black connector and the O/I switch wires.
#11 Push loosely assembled unit onto fan assembly ensuring correct funnel seating. Secure the entire assembly by replacing the three screws.
#12 Connect the black connector to the ice maker head. (Match up the holes)
#13 Check your work. (If you forgot something or misrouted your wires you may need to take it apart and do it again).
#14 Remove O/I switch from old unit. (Use a small screw driver to pop out and needle nose pliers to carefully remove the connectors). CAUTION: Be very careful as these switch connectors are not very robust and can easily pull right out of the switch if not done very carefully. (Why a new unit doesn’t come with a new off/on switch is beyond me).
#15 Push O/I switch into place on new end cover. Install power wires.
#16 Carefully push the cover onto the head ensuring the cables do not bind or get pinched.
#17 Check your work.
#18 Install plastic flapper onto the control rod. (This takes a little study to get it on right).
#19 Install control rod/ flapper assembly into hole on the ice maker. (Note: Ensure rod is all the way in and that it also goes through the hole at the opposite end. The position seems a bit odd at first but after the ice maker cycles it will drop into position. This is needed to let the ice maker know when the ice bucket is full of ice).
#20 Carefully slide assembled icemaker into freezer. (Mine was tight but it will slowly pop into place). Ensure the catch pops back into place. Observe the rubber hose protruding from the roof, it should be directly over the small funnel.
#21 Reattach the wiring harness.
#22 Reinstall the wire harness cover.
#23 Flip the switch to on. ( O = OFF I = ON )
#24 Reinstall the Ice bucket.
#25 Plug in the refrigerator.
#26 Wait several hours and you should start getting ice.
Took bottom 2 shelves out. 2 screws held assembly in to main cabin. Remove them then 2 additional screws held drawer bracket in place. Easy yet patience and finesse is needed
Chiller Frame anchors broke off so door wouldn't stay on
Simply fit the frame onto the back piece and lined up all of the anchoring plastic hooks to reattach. I had some minor difficulty in navigating the website but the customer service agent was very helpful and assisted me in purchasing the correct part. Thanks! Gretchen
Once the part arrived, which was very quickly BTW..all I had to do was remove the old filter and then just screw the new one into place....Now I just happen to be both female and blonde but was able to get the job done in less than 15 minutes (that includes opening the box) and with very little water dripping from the old filter!!! Looks like I could work as the Maytag repair woman soon!!
