AFD2535FES Refrigerator - Instructions

I unscrewed the old filter and screwed the new filter in the way the instructions said. I have done this before with no problems. Easy fix.

I removed the bottom drawer, the two upper drawers and the glass that covered the lower drawer. Took three screws out of the left side pantry end cap and replaced it with the new part. New end cap in place, put the drawers back in, put the cover back on and it works like a charm.

I watched the video on how to make the repair. It was that easy. The hardest part was disconnecting the electrical. Once that was done it was a really simple fix.

Repair was helped by reading what others shared with similar issue helped a lot. First remove all bins and glass pane. Use the nut driver to remove three screws that hold the pantry. Be careful while removing it from refrigerator. There a an vent control that clips onto back side of refrigerator and attaches to pantry end cap. Remove this piece, be careful as not to break it. This piece ( the guts) attaches to the slide piece that attaches to the controller, remove carefully by turning it to align the slot tab. Then remove the pantry sliders by two screws by using your nut driver. Reverse these steps for reinstall. Then place completed unit into refrigerator, by clipping the back vent control, don't forget the square foam gasket. Then slide the pantry end cap into place, pay attention to the front of the end cap as you may need to slide into the clip to lock in place. Then screw in the three screws, careful not to tighten to much, as it might crack.

I removed the cover on the water dispenser and replaced the parts with new parts ordered. The switch corrected the problem.

Unscrewed bolts pulled out motor,unhooked motor,replaced with new motor,put back in and replaced screws..fairly easy..then we had ice that evening!

Video instructions walked me right thru it had no problems.

turn power off, take the little cover on front of ice maker off so you can pull ice maker box out easier, unplug the easy connector ,after this take square cover off you'll see control motor take 3 screws off pull control motor out change new one in ,put them back together.turn power back on .then now Ice Maker will make some after 2 hours .You will SMILING then say ,Oh Yeah. QT good luck to everyone

The online video shortened the learning curve, and the cut the repair time in half.

Put part on /did not see warter come at first had to go a cycal then ice again thanks alot, danny repair guy whanted 46$ to look at part. Good job.

My ice maker has been broken since august 2011. I called my son in law, which is very handy, he looked at the broken ice maker, said he had no clue how to fix it, since its computerized. Searched the internet, found part select website, watched videos, read customers feed back, based on information provided, ordered icemaker control and motor assembly (less than $60. 00), Called my son in law, in less than 10 minutes, part was installed. The next morning the ice bin was full. I am so greatful for your website, and my wonderful son in law.

Screwed new filter in

Watching the video made this dead easy. If I had a newer refrigerator, I suspect it would have taken 10 minutes. Since I have an older 'fridge, I ran into two issues not in the PartSelect video. First - there were no "clips" to slip the icemaker into/out of, the unit was screwed directly into the freezer wall. Kinda hard to see the screws, especially the one in front, but not a big problem. Second - there is a wire-harness clip at the back side of the icemaker, that hooks onto the ledge of the back connector, just under the screw. That clip had slipped, and until I figured that out and reseated it, it made getting to the rear screw wit the nutdriver a serious pain. Other than those two issues, though, the job was exactly as easy as the video makes it look!

Cubes in bin were freezing together due to water leaking from the ice maker assembly. Replacement went easy with bin rails removed.

1. removed bottom screw. 2. pinched sides of rear connection to disconnected ice maker (noted red wire on top in cabinet rear). 3. bump out old unit taping to release tab on bottom. 4. disconnect wire from icemaker and remove wire holder with philips screwdriver.ew ice maker. 4. reattach harness to new ice make and replace clip. 6 reattach l bracket to bottom of ice maker. 7. detach shut off wire from old ice maker and replace on the new maker. 8. place back into position in freezer compartment. 9. reattach water delivery tube 10. connect wire to rear of cabinet. If motor drive still good on old maker scavenge before throwing away bad parts.