AFD2535DEW Amana Refrigerator - Instructions

I ordered the grill without listening to the advise given by the operator and ended up reordering the correct part. Ya just gotta listen to the people who know or else. But The order was filled in record time with absolute perfection and the instalation went fgast and easy. Now, my wife is a very happy camper... thanks to the very kind, helpfull and professional folks at PartSelect. Lamont.

I took all the food out and the shelves above the area. The end cap was a piece of cake to remove, only two screws to take out, and installing the new ones was very easy.The reason it took so much time is because I thoroughly cleaned the fridge at the same time.

Dropped down the front control panel were you program the the tempertures when you open the doors. This just pops down from the front. Then change out the printed cicuit broad two wires all done.

The ice maker stopped making ice. Cold water was still available at the freezer door dispenser which seemed to isolate the problem to the ice maker control board/motor. My ice making unit was not identical to the one in the video, but close. After disconnecting the power, I was able to replace the control board/motor without having to remove the entire ice making unit. Total time for repair was under 15 minutes.

Undid the bolts to the ice maker, unplugged it and took it out of the freezer. Removed the cover, unplugged the motor and unscrewed the motor from the casing. To install new motor screw it into the casing, plug it in and replace the cover.

Removed items from frifge, took out the lower drawer, removed side plate with broken part by nutdrive, replaced it, and put everything back - about 15 minutes. Easy.

Logged in to internet, for whatever reason I selected your site. Good choice! Entered the model number and selected the symtems identical to my refrig. Ordered the recommended parts, (Relay and Start Capacitor), to solve the problem. Reviewed the remove and install video. Received parts as promised by del date. Installed parts under 15 minutes, Frig kicked in and frig has been working beautiful. Avoided all those added expenses of; home service check, amount of days in- shop repair, plus parts and overhead charges. Will recommend site to my friends.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Since I had more than one issue, I decided to replace the entire ice maker. All I needed was a nut driver and it took 5 minutes. Three hex screws and unplug the wire harness and the whole unit came out. I changed the harness over and installed the new unit. I left for work and came home to ICE. It was Great!!!

After one attempt to use super glue failed, obtained the part (shelf support). Had to remove drawers and a shelf to get to the support. Two hex screws held in place. No problems, a little touchy to put the lid back on, but all in all a simple repair. Didn't have instructions - didn't need them - it was straight forward.

Removed large lower drawer, removed contents from the lower shelf, removed the two produce drawers, removed glass shelf. At that point you will be able to remove the three screws from the left side pantry end cap. A slight upward and forward motion will release the side pantry end cap once the screws are removed. Once the side pantry end cap is removed, two screws will removed the drawer track. Note: you will have to slide the drawer track one way or the other to align a small hole to find and remove the hidden screws. The process was reversed to install the drawer track and side pantry end cap, etc. The actual removal and installation of the new side pantry end cap took less than 10 minutes. I was very pleased with the ease of ordering and speedy delivery of the part from PartSelect.com

initial research suggested that relay is common failure point -opened back panel and found that relay was "truly smoked" - black soot came out when I removed it and shook it also checked that the compressor itself wasnt damaged using the resistance check across pins and also from pin to outer cover - determined that the compressor seemed OK and fault likely isolated to relay - - overload cap seemed to be ok - but decided to replace entire unit (relay and cap) - ordered on partselect.com - video showing how easy repair was very helpful - replaced it - and DONE!

1. Viewed the video furnished (very helpful) 2. Turned off circuit breaker (avoids having to move the refrigerator), took my chances and left the water on 3. Removed the ice bin 4. Removed bottom retention screw, loosened the top two screws 5. Lifted the old ice maker free of top two screws 6. Used the bright flashlight to see how to release the rear electrical connection 7. Placed old unit on toweling, removed the electrical harness, the bail and the lower retention offset bracket (needed because the Kenmore's bottom retention is toward the center of the ice maker) and reinstalled them on new unit, taking care to maintain the original harness clip method 8. Carried the new unit to the refrig and installed the rear harness connector, then lifted it to mount on the top screws, forced it down to correct position, installed lower screw and tightened all three. 9. Placed bail in 'Operate' position, Installed bin and turned on the power. 10. Next morning, success!

The right hand pin that holds the liftable clear door over the lowest drawer broke. It is a molded piece, so the whole right end cap had to be replaced. The large lower drawer, the two smaller drawers above it and the glass divider/shelf all had to be taken out. The end cap was removed using a 1/4" allen wrench hand driver, and the whole assembly had to be angle out at abour 45 degrees to release a connect temperature control slide from a slot in the back of the refrigerator (I was not expecting that, but it was not hard to free it). Several pieces had to be removed from the orginal end cap and placed in the same position on the new unit. I did this without looking at any instructions (of course), and it took a few minutes to figure out how to get it apart. Previewing instructions would not be a bad idea for those who don't want to figure out the puzzle. Reassembly was easy, and I then just reversed the process to put the fully assembled unit in its' place, put the drawers and shelf in and reattach the liftable door to the pin.

Removed fill tube and replaced it with new.