AES3540BAW Amana Range - Instructions

Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.

It was really easy. It took about 5 minutes to remove the screws holding the back in place. Another couple of minutes to remove the switch, and a few more minutes to change the wires over one at a time. Then 5 more minutes to put it all back together again, and plug it back in, and it just worked. Really simple.

Remove the door, remove screws from all sides

Remove sides and face of oven door by sliding down from under the oven handle trim.

Remove screws on 2nd light of glass and set aside.

Now you are at the inner door panes. their should be two in an insulated type unit.

Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.

Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)

reassemble door as it came apart carefull not to over tighten the screws, they strip easy.

From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.

Put a new one in.

First be sure to unplug stove or turn off from breaker switch. I Removed racks from oven . Using screwdriver I loosened the back plate in the oven that held the wires connected to heating element , being careful not to let wires fall through holes . Gently pull element tip apart from wire. Snap end of new element to wires, screw plates back to tighten
Turn oven on and check to assure heating properly. Very simple

To better access the bottom screws, I removed the door by opening it to the first open position and lifting it up off the hinges. No tools are needed for this but careful, the door IS heavy! Place on table or counter top. Remove the Phillips screws, old trim, and clean the outside of door. Position new trim and replace with the new screws provided. By securing the new trim, I did not have to worry about the glass sliding out when flipping the door to clean the inside. Finish by sliding the door back on the hinges. Looks like brand new!

Side Notes: One of the side pieces of the trim was fairly bent when received. Since the misshapen piece was nicely painted i.e. parted when bent, this was a Maytag (Whirlpool) supplier issue and NOT a PartSelect issue. Rather then damaging the paint bending this piece back to fit the door, I reused the old side piece which was in great shape.

Thanks PartSelect , you're the best!

Shut off breaker, assure zero energy. Using phillips screwdriver remove old element, unplug wires from element. Reconnect wires to new element, secure screws. Assure all tools removed and people are clear before re-energizing power to range. I was not happy with the packaging, the new element came in a box with no protective packing material!

1. Shut the breaker off; Jenn-Air's design will have you working around hot leads if you don't.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.

unplug and plug in new

just plugged it in!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

I took the back panel off, removed the old lens, installed the new lens. How easy to order from home, receive the part, do the repair and pay less than it costs to simply drive to the parts house. Cool....

swap a known good coil around and still did not work. then measured voltage across the switch terminals and found out one leg was opened. Ordered a new switch which looked alike. The new switch could handle more current than the old one. Turned out that all terminals of the new switch were same size while the old one had 1 smaller size. Used the dremer tool to file it to fit the wire terminal. Also the burner knob had different grove type . Just forced it in.