AES1350BAW Amana Range - Instructions

Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.

Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.

I ordered gray enamel drip bowls and they fit perfectly. Unfortunately 2 of them were chipped and bent slightly. They still worked which was better than the make shift ill fitting ones that came with the house so I decided to keep them. I did tell parts select about it and they sent me a new order of drip pans at no charge. I used the perfect ones but the 8" drip pans flaked off paint after one use. I guess this is an Amana defect...the paint doesn't stick under heat.

Moved the Appliance out unplugged it and removed the backing plate then Remove the Knob and unscrew the infinite switch then marking the 5 wires to know where the go on the new switch, removing and replaced it with the new one

First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Failure to do so will cause the plastic plug connector to melt from oven heat.

Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.

First I removed the two philips screws inside the oven that hold the element in place. Then I pulled the sensor out and the two insulated wires through the hole to reveal the plastic connector. I unsnapped it from the connector and replaced it with the new element. Then, behind the oven, I removed five or six philips screws on the right side of the large panel so I could pull the wires back through the layer of fiberglass insulation to make sure only the sensor itself would be exposed to the oven's heat. I then secured the back panel again and replaced the two philips screws holding the sensor in place.

First I opened the door to the oven. Then I opened the box that the part came in. (knife) I then slid the oven rack out of the box and unwrapped the plastic, being careful not to bend or scratch the new rack. Now, this is the tricky part... I had to move the existing rack down one space to make room for the new one. Then carefully slid the new rack in, tipping it slightly and sliding it in. LOL

removed back cover
removed wires
removed two screws and removed switch
replaced switch and two screws
replaced wires and back cover

unscrewed and unplugged the old one and plugged in and screwed in the new one. EASY!

Pulled oven out of the cabinet/wall and pulled sensor out and replaced with new one.

A few years previously I had this same problem and a PROFESSIONAL had replaced the sensor.
Thus this time I knew what the failure was and obtained the sensor from Part Select. Having observed the PROFESSIONAL replace the sensor before; I followed his easy technec only to learn that when the sensor was pulled from the aft wall of the oven that the wires had deteriorated and the plastic plug melted. Therefore it was neccessary to remove the oven from the wall cabinet. Then I removed the panel from the back outside of the oven, cut back the wires and because the kit from Part Select contained additional connectors was able to splice in a replacement connector. Installed the new sensor and reinstalled the oven. LESSON LEARNED; when the PROFESSIONAL had replaced the sensor he had failed to feed the wiring and plug back past the insulated chamber, directly behind the oven, into the cool area assessable by the panel on the aft side of the oven thus the plug and wires were exposed to the heat of the oven. What would commonly be a few minutes job turned into an afternoon project.

Removed the old sensor by removing two screws and pulling the wire out through the hole. Disconnected the connector and discarded the old sensor.
Selected the correct connector of the 3 provided, plugged the new sensor in and threaded the wire back into the hole paying special attention to make sure wire and connector was on the backside of the insulation. Assembled the two screws and tightened.

Removed 2 screws holding element to stove then gently pulled element forward to exposed lead connections and disconnected leads to element then reconnected leads to new element and gently pushed element ends back into the openings in the back of the stove and replaced screws to hold element to stove

This purchase was for replacement parts, not for repair. Installation was a simple matter of taking out the old and installing the new, which is extremely easy to do. One item was damaged; Parts Select was absolutely fantastic to deal with regarding replacement! One word of caution regarding the product - I mistakenly ordered Whirlpool drip pans which have an opening in the bottom, the Maytag pans don't. Initially I thought that it was a mistake by Parts Select; which wasn't the case. The pans fit perfectly so I kept them. If I reorder, I will be certain that I order the correct pans.