All Installation Instructions for General Electric Dishwasher ADW1100N00WW

Door latch broke

Removed the old one from its slot and slid the new one into it.
No instructions needed.

Parts Used:

Door Latch Kit

Barbara from TAMPA, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dishwasher would not start

Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell

Parts Used:

Interlock Switch

Dameon from SMYRNA, DE
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Water leak under Unit

Remove Base Access Panel; Removed Valve Mounting Bracket & Valve; Disconnected Wire Connector; Disconnected Supply Line & distribution Hose; Reversed the Process. Piece of Cake; Part was O.E.M.Component Exact Fit; Took Longer to Write this than it took for Fix. Thanks I Will Be Back for other Parts.!

Parts Used:

Water Inlet Valve

GEORGE from LEVITTOWN, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

8 of 16 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dispenser cap would not stay in place because it had melted

First I opened the package and screwed the new dispenser cap into place.

Parts Used:

Rinse Aid Fill Cap

Patricia from Clifton, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Upper rack kept dropping from the wheels when we pulled it out

We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.

The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.

Parts Used:

RACK SLIDE END CAP

Joel from Cypress, TX
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Missing wheels

Inserted wheels on socket and then into the dishwasher rack.

Parts Used:

Lower Front Dishrack Wheel

Felix A from Orlando, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Disrack was getting rusty

Removed old rack replaced with new one which was an exact duplicate. Mama's happy; everybody's happy.

Parts Used:

LOWER RACK

Nelson from Oroville, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

rack slide end cap missing

installed part on inside end of rail. no tools needed. original part wouldn't stay on rail. finished in 2 minutes
wife happy

Parts Used:

RACK SLIDE END CAP

Carrell from Cochranville, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

detergent shaft and arm broken

pretty easy, take off 7 screws from inside door

only hard part was getting arm to click into lever through the door. if you practice with the parts outside the door they lock together really well :)

Parts Used:

Detergent Cup Release Arm

Detergent Cup Shaft and Lever

Michael from Shelton, CT
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

5 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dishwasher would not drain

Watched a YouTube video description of the repair and ordered parts from this site

Parts Used:

Inlet Sump

Pump Filter Coupler

Tom from Magnolia, IA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Would NOT drain

Flipped washer on side
Did repair from bottom
Really easy repair

Parts Used:

Motor and Drain Pump

Nathaniel from HAWKINSVILLE, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Water leakage at valve

I watched the video that came with email on part. Gave instructions on how to. Thank you !

Parts Used:

Water Inlet Valve

Jimmy G from SPRING, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench (Adjustable)

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The telescopic part of the washer was broken.

The part came in as ordered. After removing the dish rack, I loosened three 1/4" screws (two on the strainer basket and one at the base of the spray arm. I had to slide the rubber hose down and back to disconnect the base which I did by turning counter clockwise. The new one went in by reversing what I just described. Other than two of the screws being difficult to reach, everything worked fine.Thanks for your site.

Parts Used:

Lower Spray Arm

Jeffery from DOUBLE SPGS, AL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set, Wrench set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Upper and Lower racks had rusted

It was really simple. I watched the u-tube video to replace the top rack. I was able to complete removal of the old one and replacement with the new one in about 5 minutes. The lower rack simply pulled out and the new one slid right in. The quality of the replacement racks is much higher than the originals. I'm so happy I chose this easy and cost efficient repair.

Parts Used: