ADB1400PYW2 Dishwasher - Instructions

I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.

I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.

Well, it’s very easy to repair. But, what I like if ur Company is, the availability, of the parts.
Thanks you.

I just snapped the old one off and snapped the new one on..

based on advice here, concluded the problem was likely that the part "Valve-Inlt" was defective. Our dishwasher intake line is copper and had already developed a partial kink from sometime in the past, so I had to be careful. The final connection to the new part had to happen in place: very close to the floor and underneath, because I didn’t want to stress the copper line. Plus, the shutoff was defective, and it was always leaking while I connected. Awkward. As I was threading on, it started to look like it might be cross-threaded, so I stopped and reversed. Slid the washer back out and disconnected the drain line so I could tip the dishwasher u and inspect. It was going on cross-threaded. Not hard to happen on a metal to a plastic connection. To solve, I carefully made very small bends in the copper inlet line until when it would later be brought up underneath to connect to the inlet valve, it would be as perfectly aligned as possible. This worked. As I tightened, it went a little easier and the leak stopped. A good moment. Tightened a bit more, but didn’t want to overdo it as that can cause other problems. Now the moment of truth: let’s run it. DISHWASHER WORKED AGAIN. Runs fine now and we are glad to have it back. Was satisfying I could do this on my own. The advice and guides here made that possible. Thank you.

Tipped over washer, removed attachment bolts, installed new pump by clamping water hoses. Be sure to use proper crimping pliers, not the generic slip joint pliers. Replacement pump included required new clamps.

Very simple to repair The front track stops just slide into place, easy. When I looked for these parts this place was the least expensive and the quickest delivery I have ever had. Quick, efficient and friendly online staffing. Thank you, Deb

watch how it was done on computer

Replaced the strainer. This keeps the two sprayers clean/clear so they do not clog up. Dishes are cleaner now. Note : if your sprayers are clogged it is a long process to clear out the sprayers. Dishes will not be clean until your sprayers are all cleared.

After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.

The video included with this part is perfect. Unplug the dishwasher, take off the front trim piece, remove the drain hose from the pump, unclip the power, press the little clip that holds the pump in while turning it counter clockwise to remove. Then just do that in the opposite order to put the new one in. Just make sure you hear it click when you twist the new one on so you know the clip has engaged. Super easy.

As stated above the repair did not go well because the gasket was too wide and the door would close. Suggest you talk with Whirlpool about the part they sold you for my model of dishwasher.

Followed very simple instructions to easily install. The only tool needed was a flathead scredriver to pop off caps to remove old, broken rollers. New rollers simply click into place. Piease aren't cheap, but significantly less than a new dishwasher.

I followed the video provided by this site. It was perfect and made the job very easy.

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.