ACS7270AW (PACS7270AW0) Amana Range - Instructions

I removed the two screws and pryed out the old hinge. I then put in the new hinge. The new one fit well. I went to screw it in with the supplied screws. The screws not only did not fit the hole tapped in the hinge (too big, different tread) but both screws were different from each other. They were different sizes and different types all together. I tried re-using the screws from the originol hinge but they also did not fit. I then got my own self tapping machine screws and finished the job. This job should not have been that hard. If they had supplied the correct screws, It would have taken all of five minutes.

So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.

Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.

I removed the whole back panel and everything else seemed OK visually.

1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.

2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.

3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.

I didn't. Don't know how to get to light bulb to change it for this specific model

A Home Depot employee advised me on how to enter all my oven information found on the front of my oven on parts.com. I submitted parts information as stated, also very easy. My parts arrived 3 days later. I used a screwdriver & pliers, it took less than 15 minutes. Very simple and the entire process from order to installation went like clockwork. I would definitely order in the future. Thank you.

First we turned off the power to the range top. Then propped the range top on small planks of wood in order in order to get to the 12 to 15 screws that held the top to the base. Once we had the top (glass) removed, we removed the four screws holding the bracket that held the front and rear elements. We then removed the bracket and elements, turned the bracket and elements over to remove the two screw type legs that held the dual element. Once the dual element was loose we disconnected the wires and reconnected to the new element. Then reversed the procedure to reinstall.

First turn off power to stove with breaker or unplug it. Then remove three screws under the front of cook top, and lifted up cook top from the front. Then brace it up with a stick about 20 inches long so you can work. Now locate the latch at the front of range. Next get some paper and labeled where each wire is connected by color. Remove wires from old part, next take out two screws by the front of part. Remove a clip on left side of part that is holding the wires. Take old part out and replace with new part, put back the two screws in front of part. Next put the wires back on using the list you made. Then replace clip to hold wires. Now turn power back on,or plug it back in. Reset clock and your done.

Instructions with parts are minimal. Looked at exploded drawing and read other installation descriptions on site. From the read I knew it was easier than it looked. Opened oven door. Unscrewed screws about 1/3 of the way up on both sides on inside face of door; these are the only thing attaching the hinges to the door. (Save all the screws you remove - they make work better than the ones with the parts.) The door can now be pulled off the range. I pulled the broken part out of the right side with pliers. Remove the screws below and about 8" up from the hinge on each side. When this is done you can pull the hinge out from the slot from the front. Open the new hinges up and they will slip through these same openings and position them as the ones you removed were positioned. Replace the screws. On the parts I received the lower screw holes on the hinge were not tapped. The original screws worked a bit like self-tapping ones. If you lose any parts or need to get to the hinge from the back you can take out the drawer.

Subject range is in a rental house and receives much use and abuse. The repair was necessary due to the door having 2, 1-2 inch cracks one on each side so the door bent outward. Obviously in the past when the oven door was completely in the open position much weight was placed on the door cracking the sides and bending the door. Consequently, when the oven was in use and the door was closed being that the door was bent outward heat escaped from the top of the door heating up the control panel. The control panel would get so hot that it could not be touched without burning the fingers. Replacing this range would cost approximately $2200, so we had to try to repair it. I went to the ParSelect website and ordered the part I needed.
Being that the oven door is heavy and large it took two people to disassemble and reassemble the door. We had quite
a wrestling match with the door (consider too, that we never do this type of job) but after about 3 hours our range was almost like new.
Disappointing that a replacement mylar cover for the control panel is no longer available at PartSelect. We would appreciate getting our hands on one as the existing mylar cover is cracked.
The oven has been successfully used since the repair and we have a good fit and the control panel is now only warm instead of blistering hot. FANTASTIC!
THANK YOU


Time will tell.

Sincerely

Craig and Judy Crouch

First I removed the two screw on the lower inside of the door that hold the door to the hinges. Then I opened the oven door at about a 15 degree angle, and carefully lifted the door out of the hinge brackets. Next I had to remove the side panels on the door . After getting those side pieces off, I realized that I had to go through all layers of the door to get to the inner glass, so I decided that the best way to keep track of all those screws, was to remove each screw with the Phillips head screw driver, and immediately scotch tape that screw right next to the hole it came from. That was the best idea I had, because there are many screws in that door! Removing the old glass, and replacing it with the new glass was the easiest part of the project, just be sure not to let pieces of the insulation get between the glass and the metal frame. Then I reversed my steps to put everything back together. It probably took a bit longer than someone else because I first taped each screw on the panels, and then had to remove the tape, but I just did not want to find a handful of screws after the door was back on, or worse, somehow lose one or two. I think the hardest part of this project was getting the door back on the hinges, because the door is heavy, and you have to line up the hinges with holes in door, and slide the door in evenly. Once the door is back on, re-insert the two screws, and your oven door is as good as new (and as clean as new).

I was surprised when I was able to find that the (10 year old) parts for one of the drawer slides of my stove were still available. However, I was disappointed that the small bolt that I ordered did not come with a nut. I was lucky to find one in a collection of nuts in my workshop, and so was able to fix the slide. However, I suggest that if you supply someone with a bolt, that you include the nut that is necessary to make it work.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Indicators showed broiler should be working so basically made a guess that the element was bad and replaced it. Turned off circuit breaker and removed mounting screw and unplugged terminal ends of the element and replaced with new one. Switched circuit breaker on and turned on broiler and my repair was a success.

The repairman that had come had stated that this part is no longer made, but I was able to locate one through PartSelect and was able to replace it with minimal effort.

I removed the three screws that held down the stove glass top surface and had a person hold the stove top up while I removed the two screws which held the autolatch assembly in place. I then swapped the leads from the failed assembly to the new one and replaced the screws which were removed. New assembly tested out fine and oven was able to self-clean again.

removed 2 screws holding top in place witch gave me ac access to none working part. removed 5 screws witch let me remove part, reversed order to reinstall part, very easy
Donald Carpenter

Remove three strews and two wires. Less than fifteen minutes for this Seventy Seven year old farm boy!