Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
no power at all
unscrew microwave's cover,test the fuse which is located at top rear left side, the fuse is inside a plastic tube,if the fuse is burnout,just replace it.
Turned the microwave on its side. (Recommend turning it on its top. i had to fish the wire connection back to the center after it dropped away from the motor.) There is a spot under the rotation motor where an access port was stamped in the tin but not cut out. Used the small side cutter to complete the cut where tin had been left between holes. I unplugged the wires, removed the old motor by removing one screw, and installed the new one by reusing the same screw. The motor must have a reduction gear inside the case. The motor coil tested good, about 128 ohms, but it acted like there was a stripped gear inside. I wasn't interested enough to try to open the motor and confirm.
Had to go to the garage and get a small sheet metal screw to close the new trap door.
The "new" motor had scratches on it, made me wonder if it was really new, but it works fine and will probably outlast me.
Had to remove unit from above stove, this step will take the longest. With unit on table cushioned with a throw rug under it . I removed the case and located the magnetron removed 3 screws, unplugged unit with a needle nose pliers, installed new unit plugged it in and checked the microwave with a cold coffee cup of water . Worked great! Heated great!
Plate stopped rotating - discovered plastic piece that spinner fit into was broken
Remove 2 Philips Head screws on left side of microwave. Remove 3 Philips Head screws from bottom rear of microwave. Remove 4 security screws from back of microwave (holding the cover to frame). These are the security type tips that are like a Torx bit, but need to be hollow in middle to accommodate pin in center of screw. Then back plate of microwave with heavy transformer still attached slides up and away. The wires aren't long enough to allow it to rest flat on the bench, but weight is low so it's easy to hold it upright while removing the motor unit. Separate connector from motor (simple) Remove motor by unscrewing 1 phillips head screw and rotating counter-clockwise a tiny bit. Remove Motor. Reverse steps to re-assemble. Note that there are a series of tabs at the bottom of the back cover that fit into holes in the baseplate of microwave. It can be a little tricky to line them up with the weight of the transformer, but it's not too bad. Once lined up, it drops in nicely and all the various screw holes line up. The microwave is a bad cooker when the plate doesn't spin. This simple and inexpensive fix saved me from having to buy a whole new oven.
Watched a you tube video prior to installing new switch. Followed the video which gave me confidence i was up to the task. After removing the touch pad I found my design was not exactly like the you tube model but I found the defective switch, replaced it and put the microwave back together. Works great. Again watch the videos
Microwave fan would come on when door open. Timer and unit would not switch on.
I looked up my problem on the internet and found a very helpful video. Microwave on video was different brand but the internals and methods were very much the same. The video made it simple and easy to fix. Found the replacement switch on the LG parts site and ordered. Two different switch types. One with red switch, the other green. Part was $7.28. Saved a bundle in service costs. Here is the repair video.
Remove the rear casing of the microwave using both a Phillips head screw driver. The lower rear screws require a star shaped bit with a hole in the middle (security bit). Once the rear casing is removed, it is very easy to access and replace the bulb. But the bulb sent was NOT identical to the original which has a straight fitting into the receptacle. The one sent had a fitting with a 90 degree. The bulb did not quite fit in place, but I secured it with some black electrical tape.
Take off cover then the bottom. Transformer is on the bottom plate and wires won't let it come all the way off, too many wires to pull off so will have to position the bottom plate so you can get to the motor. Remove 1 screw on motor and remove motor. Install new motor connect wires replace bottom plate, replace cover. All done (hope & pray it works ok) mine worked perfect. Hope this helps.
Overall repair quite simple. Removed screws from the sides and rear of the microwave, then removed cover. Next, removed only the screws to separate the bottom cover. Removed the one screw in the AC Synchronous motor to remove the motor (had to use small screwdriver through a vent slot in the bottom to remove the screw). Unplugged and removed motor. Installation is the reverse of removal. Note: on the back of my appliance were 4 torx screws with a tamperproof pin in the center. I used the rotary tool to grind out the pins so I could use a regular torx bit instead of ordering specialty bits.
synchronized motor died a terrible death and stopped turning.
Eight screws off the bottom exposed the cover plate. Easily found the motor location the looked up the item number and verified data and ordered the part. Replaced the motor, tightened the screws and flipped it upright. Plugged it in and the lights came on. Set a time pushed start and smiled! The eagle had landed!!!!
All the electrics worked on Amana microwave EXCEPT for the cooking function. Inspected the control board and found the upper switch on the door interlock was burnt. Installed new switch in minutes and everything now works fine. Unfortunately, had to purchase expensive two switch "kit" although only one switch was kaput. PartsSelect mailing was SUPER fast. Thanks for looking, Scott
Carousel would not turn. Small plastic drive shaft broken.
Pried cover off bottom-center of microwave. It seems to be either glued or lightly tack welded. Removed 2 small Phillips screws to remove motor. Disconnected electric feed by hand. Don't let go of electric wire or small screws. They will be hard to retrieve from behind the rest of the metal base. Reverse process to install new motor. Didn't try to put small cover back on.
1. Remove the trim frame off of the front of the cabinet (4 Phillips screws). At this point, take glass plate and turntable frame out of unit. 2. Slightly lift the unit off the cabinet frame (which is attached to the cabinet) so the feet on the microwave allow the unit to clear the frame and then remove microwave from the cabinet. 3. Once slightly removed from the cabinet, unplug the unit before completely removing it from cabinet. 4. Take 2 Phillips screws out of the side panels. 5. Take about 6-7 T20 Star Pin screws out of the back of the panel. (This may require you to purchase this special tip if you don't have it in your toolbox). 6. Slide the microwave cabinet toward the rear of the unit (the front portion clips into the frame ... don't try prying it off because you'll damage the unit). 7. Completely remove the microwave cabinet housing. 8. Be careful not to damage or catch any internal wiring inside the unit while the cover is off. 9. Turn unit on it's back and remove 4-5 Phillips screws holding the bottom cover in place. Remove bottom cover. 10. Now notice that the turntable motor is completely exposed. 11. Remove the wiring harness from the motor (notice which connection clip has the black wire). 12. Remove the one Phillips screw holding the motor to the frame. 13. Clean around the area in case food spills may have gotten into the area. 14. Insert new motor, put Phillips screw back in and attach power connection. 15. From this point on, just reverse steps to re-assemble microwave and put back in cabinet. 16. Test new turntable motor. 17. Enjoy the smile from your wife because she can now use the microwave!
the turntable on the microwave quit turning even though the microwave would heat up
I removed the outer cover of the microwave and removed the bottom palte to access the small motor. i unplugged the old motor from teh wiring connector, removed (1) screw and motor came out. I reversed the proceedure with the new motor and it was finished.It was a piece of cake.
