AAV2200AGW Admiral Washer - Instructions

First I replaced the Snubber but after I tried the spin cycle, the washer still made banging noises. I removed & replaced all 6 Suspension Springs & now the washer works like a dream

Following the other repair examples posted. Replaced Snubber Ring and 6 tension springs. Washer works great again. No more dancing in the hallway.

Determined it was the pump through listening to where the noise came from by taking the back panel off for easy access. The pump is at the back of the unit and was easily accessable. The Motor is on a pivot bracket with springs, so it was easily moved to loosen the belt for removal. After removing the 2 drain hoses with the pliers, the pump came out with 3 screws. Replace the new pump with the reverse procedure. It worked perfectly.

Used pliers to remove spring clamps on either end of hose. Removed hose. Put clamps on end of new hose. Slipped hose ends in place and re-secured with clamps. Another save by PartSelect!

Posted instructions/videos were on the mark.
Some springs are more difficult to reach, so disconnecting the entire cabinet from the base to gain access from different angles helps a lot to connect/disconnect the springs.

Watched videos on how to replace the hose. Armed with the information I started the process. But the videos were wrong. After removing a bunch of screws and not getting to the hose I removed the inspection panel on the rear,three screws and there was the hose.simple. I wished I had not watched the videos.

I remove the necessary panels, hoses and electrical section and removed the tub springs and pulled the tub assembly out of the unit and replace the snubber ring. Was really not hard to do and it worked like a charm. No more problems :)

Disconnect AC, turn off water pressure, flip it backwards to remove the drive belt below, open back small panel (4 screws), Use pliers to disconnect hoses from drain pump, and finally remove the 3 bolts, and walah, reverse procedure and tell your spouse what a hero you are.

First thing was to go to PartSelect website to see what others with the same problem did to solve their problem. It was 45% pump and a lot less for the belt. My belt is only a year old so that was out. I ordered my new pump and watched the video on PartSelect a couple of times. I didn't bother to disconnect the water and drain lines. I had my wife hold a plastic 2 quart container under the pump when I pulled the small hose off and didn't spill a drop. Like the man on the video said...the new pump isn't identical but it fits and works fine. Thankx PartSelect!

installed new pump, 10 min. job

very easy repair, acess from the back, just a 1/2 dozen screws to change

Simply followed the instructions on the video provided and the repair was a breeze - quite impressive service!

Removed and placed new one in 15 minutes. Thank You so much for the help

placed washer on front exposing bottom of machine. removed clip holding pulley in place with needle nose pliers. The old parts slid off transmission shaft easily. I set these aside in order of removal. The replacement parts were not exact matches to OEM parts replacement bearing was heavier duty and thicker there were washers in the kit that would not even slid onto transmission shaft,replacement pulley and cam were exact replacements for OEM. I replaced the bearing and thrust washer and then used a combination of new and old washers to build the assembly back to the original length so the retaining clip would hold assembly firmly in place.The instructions key point was that the final height had to bring the pulley back to the original height for a snug fit with retaining clip. Once I realized this the extra parts in the kit were less worrisome.

Easy fix. I pulled the washer out from the wall and leaned the top back to the wall. I then removed the belt from the bottom. I set the washer back on all fours and slide it around so I could get to the back water pump access panel. Using a nut driver, I removed the screws from the panel, then I removed the panel. I could now see the water pump. With a pair of pliers I removed the two hose clamps, and removed the end of the hose's from the pump. Then with a socket wrench I removed the three screws holding the pump down and removed the pump. In reverse order I put it back together. It works fine and saved me a lot of money from happened to buy a new washer. Thanks PartSelect.